Table of Contents
Advertisement
Quick Links
TECHNICAL PROGRAMMING MANUAL
READ:
• selection of functions on page 5
• when terminal 65 are connected is necessary
programming ADJUSTMENT WITH CHARGING
ALTERNATOR FREQUENCY (W) see page 6.
ELCOS- Parma- Italy - EN - DCA-120/10
BRIEF INSTRUCTIONS
Valid for firmware revisions higher than or equal to 1.34
Tel. +39 0521/772021
Fax +39 0521/270218
®
1
Advertisement
Table of Contents
Related Manuals for ELCOS DCA-120/10
Summary of Contents for ELCOS DCA-120/10
- Page 1 • when terminal 65 are connected is necessary programming ADJUSTMENT WITH CHARGING ® ALTERNATOR FREQUENCY (W) see page 6. Tel. +39 0521/772021 Fax +39 0521/270218 Valid for firmware revisions higher than or equal to 1.34 ELCOS- Parma- Italy - EN - DCA-120/10...
- Page 2 After 30 seconds of inactivity, the control unit enters STAND BY state, switching off completely all the signalling (led and display). To exit STAND BY state press one of the buttons. Valid for firmware revisions higher than or equal to 1.34 ELCOS- Parma- Italy - EN - DCA-120/10...
-
Page 3: Table Of Contents
ANOMALY Complete reset of the log. Volvo CAN Bus Acceleration VOLVO TAD 124X Joint A PARAMETERS SERIAL PORT RS332 Serial port RS485 parameters. Valid for firmware revisions higher than or equal to 1.34 ELCOS- Parma- Italy - EN - DCA-120/10... - Page 4 ELCOS- Parma- Italy - EN - DCA-120/10 Valid for firmware revisions higher than or equal to 1.34...
-
Page 5: Choice Of Functions
Press and wait for Press to PROGRAMMED to be written Press when the arrow is next display to the unit of measurement to be modified. Valid for firmware revisions higher than or equal to 1.34 ELCOS- Parma- Italy - EN - DCA-120/10... -
Page 6: Running Engine
Press to choose the number of rounds at wich TACHOMETER and OVERSPEED the starting motor has to be disconnected. no adjustment Adjustment field 300 ÷ 4000 RPM. Valid for firmware revisions higher than or equal to 1.34 ELCOS- Parma- Italy - EN - DCA-120/10... -
Page 7: Preventive Maintenance
RESET ANOMALY CAN BUS? RESET ANOMALY CAN BUS? STOP To reset press simultaneously and Press to wait for PROGRAMMED to be written display Valid for firmware revisions higher than or equal to 1.34 ELCOS- Parma- Italy - EN - DCA-120/10... -
Page 8: Relays That Can Be Associated
0÷300 zero operation Engine deceleration time. excluded WEEKLY AUTOTEST TIME 1÷60 3 minutes When the test time is up, the engine stops minutes Valid for firmware revisions higher than or equal to 1.34 ELCOS- Parma- Italy - EN - DCA-120/10... - Page 9 Time 3 min TIME 3 min STOP Press to Press and wait for display Press to change the time PROGRAMMED to be written Valid for firmware revisions higher than or equal to 1.34 ELCOS- Parma- Italy - EN - DCA-120/10...
- Page 10 During the norm al operation the MEMO RY “ DOES NOT STOP ERROR m em ory is no longer used. Valid for firmware revisions higher than or equal to 1.34 ELCOS- Parma- Italy - EN - DCA-120/10...
-
Page 11: Engine Programming
Press and wait for Press to PROGRAMMED to be written Press when the arrow is next to display the parameter to be modified Valid for firmware revisions higher than or equal to 1.34 ELCOS- Parma- Italy - EN - DCA-120/10... - Page 12 SELECT PROBES SELECT PROBES ON THE DISPLAY ON THE DISPLAY THE CONTROL NORMAL UNIT IS PRO- REVERSED OPERATION GRAMMED FOR OPERATION NORMAL OPERATION ELCOS- Parma- Italy - EN - DCA-120/10 Valid for firmware revisions higher than or equal to 1.34...
-
Page 13: Transmitters
When programming just one value or non monotonic values, the fault is detected. OIL TEMP. TABLE OIL PRESS. TABLE NOT CORRECT NOT CORRECT" Valid for firmware revisions higher than or equal to 1.34 ELCOS- Parma- Italy - EN - DCA-120/10... -
Page 14: Instruments
● ENGINE POWER ENGINE IGNITION VIA CANBUS Only for engines featuring ● this control SPEED SETUP ● Only for engines featuring this control Valid for firmware revisions higher than or equal to 1.34 ELCOS- Parma- Italy - EN - DCA-120/10... - Page 15 BATTERY OVERVOLTAGE Valid for firmware revisions higher than or equal to 1.34 ELCOS- Parma- Italy - EN - DCA-120/10...
-
Page 16: Available Anomaly 1
E, 8, 1 Factory E,8,1 setting SETUP E,8,1 STOP N,8,1 Press and wait for Press to Press to choose. PROGRAMMED to be written display Valid for firmware revisions higher than or equal to 1.34 ELCOS- Parma- Italy - EN - DCA-120/10...
Need help?
Do you have a question about the DCA-120/10 and is the answer not in the manual?
Questions and answers