Casio 3482 Operation Manual page 14

iPhone Only
●
Deleting the phone's pairing
information
For details about setting procedures, see your
phone documentation.
"Settings" "Bluetooth" Cancel the
n n
watch's device registration.
If you purchase another phone
Note
Before pairing with the new phone,
●
delete the old phone's pairing
information from the watch.
Deleting Pairing Information from
l
the Watch
You need to perform the pairing operation
whenever you want to establish a Bluetooth
connection with a phone for the first time.
Pair the watch with a phone.
l C
High/Low Tides, Moon
Age, and Sunrise/
Sunset Times
You can use the watch to check high tide and
low tide information, Moon age, and sunrise
and sunset times, and other information for a
specified port.
Important!
Displayed information is intended for
●
reference only. Do not use it for
maritime navigation, etc.
To check high tide and low tide
●
information, Moon age, and sunrise/
sunset times, you need to use G-
SHOCK MOVE or watch operations to
specify the port whose information you
want to check.
Operation Guide 3482
Specifying a Port
After you specify a port, you can view its high
tide and low tide information, Moon age, and
sunrise and sunset time information.
Important!
You can select any one of three port
●
specification methods: [APP],
[PRESET], and [USER]. If you plan to
select [APP] as the port specification
method, you need to use G-SHOCK
MOVE to specify the port you want
before performing the procedure
below.
1.
Enter the Timekeeping Mode.
Navigating Between Modes
l
2.
Hold down (A) for at least two seconds.
This displays the Timekeeping Mode
setting screen.
Pointer
3.
Use (A) and (C) to move the pointer to
[TIDE&MOON&SUN].
4.
Press (B).
5.
Use (A) and (C) to select a port
specification method.
Port specification using G-
[APP]
SHOCK MOVE.
Specification of a port from the
[PRESET] list of presets in watch
memory.
Specification of a port defined
[USER]
by you.
6.
Press (B).
If you selected [APP] above, this will
●
complete the port specification
operation. [SETTING COMPLETED]
will appear for a few seconds, and then
the port specification method setting
screen will re-appear.
If you selected [PRESET] above,
●
continue with port selection.
If you selected [USER] above, specify
●
the details of the custom point you want
to use.
7.
To exit the setting screen, hold down (C)
for at least one second.
If you selected [PRESET]
●
50 ports selected from among the total of
approximately 3,300 ports available using G-
SHOCK MOVE are preset in watch memory.
Selecting [PRESET] and pressing (B) in the
above procedure will display a list of watch
preset ports.
1.
Use (A) and (C) to move the pointer to the
port you want.
2.
Press (B).
After the setting operation is complete,
[SETTING COMPLETED] will appear for
a few seconds, and then the port setting
screen will re-appear.
If you selected [USER]
●
You can configure settings for up to three
custom points.
1.
Use (A) and (C) to move the pointer to
[CUSTOM].
If you want to use a custom point you
●
previously configured, move the pointer
to [SELECT].
2.
Press (B).
3.
Use (A) and (C) to move the pointer to the
custom point you want to set.
If you selected [SELECT] in step 1
●
Select a custom point you previously
A
configured.
Press (B).
B
After the setting operation is
complete, [SETTING COMPLETED]
will appear for a few seconds, and
then the [USER] setting screen will re-
appear. Go to step 7 under
"Specifying a Port".
Pointer
14