Using The Watch In A Medical Facility Or Aircraft; Using Mobile Link With A Mobile Phone; Getting Ready; Auto Time Adjustment - Casio 5618 Operation Manual

Using the Watch in a Medical
Facility or Aircraft
When you are in a hospital, on an aircraft, or
in any other location where radio signals may
cause problems, you can perform the
procedure below to disconnect the watch from
your phone so they can't communicate with
each other (Airplane Mode). Use the same
procedure when you want to disable the
Airplane Mode.
1.
Enter the Timekeeping Mode.
Navigating Between Modes
l
2.
Hold down (B) for at least two seconds.
Release the button when the name of the
currently selected Home City appears on
the display.
Home City
3.
Press (C) 15 times.
This displays the Airplane Mode icon.
Airplane Mode icon
4.
Press (D) to toggle between the Airplane
Mode settings.
[ON]: Airplane Mode enabled.
[OFF]: Airplane Mode disabled.
5.
Press (B) to exit the setting screen.
Using Mobile Link with
a Mobile Phone
While there is a Bluetooth connection
between the watch and phone, the watch time
setting is adjusted automatically. You can also
change the watch's other settings.
Note
This function is available only while
●
EDIFICE Connected is running on the
phone.
This section describes watch and
●
phone operations.
: Watch operation
X
: Phone operation
Y
Operation Guide 5618

Getting Ready

To use your watch in combination with a
phone, you first need to pair them. Perform the
steps below to pair the watch with a phone.
Install the required app on your
●
A
phone.
In Google Play or the App Store, search for the
CASIO "EDIFICE Connected" app and install
it on your phone.
Configure Bluetooth settings.
● B
Enable the phone's Bluetooth.
Note
For details about setting procedures,
●
see your phone documentation.
Pair the watch with a phone.
● C
Before you can use the watch in combination
with a phone, you first need to pair them.
1.
Move the phone to be paired with close to
(within one meter of) the watch.
2. Y
Tap the "EDIFICE Connected" icon.
3. Y
Perform the operation shown on the
screen of the phone to be paired with.
If your phone is already paired with a
●
watch, tap
connecting with a new watch, and then
tap this watch's name.
If a pairing prompt message appears,
●
perform the operation shown on the
phone screen.
[CNCT] will flash on the watch display
●
when pairing starts. [OK] will be
displayed when pairing is complete.
Pairing started.
, tap the item for
Pairing complete.

Auto Time Adjustment

Your watch can connect with your phone to
adjust the watch's time setting.
If you leave your watch in the Timekeeping
Mode, it will perform the adjustment operation
automatically as you go about your daily life,
without any operation required by you.
Important!
The watch may not be able to perform
●
auto time adjustment under the
conditions described below.
While the watch is too far away from
ー
its paired phone
While communication is not possible
ー
due to radio interference, etc.
While the phone is updating its
ー
system
While EDIFICE Connected is not
ー
running on the phone
Note
If the watch does not indicate the
●
correct time even if is able to connect
with a phone, adjust the hand and date
indicator positions.
Adjusting Hand Alignment
l
If there is a World Time City specified
●
with EDIFICE Connected, its time will
also be adjusted automatically.
Auto time adjustment is performed at
●
the times described below.
After your phone's time zone or
ー
summer time setting is changed
After 24 hours or more have passed
ー
since the last time adjustment using
Bluetooth connection
After 24 hours or more have passed
ー
since city swapping using EDIFICE
Connected or watch operation
After 24 hours or more have passed
ー
since the last home city change or
time adjustment using watch
operation
Watch operation can be performed
●
even while it is connected with your
phone.
6