Using The Appointment Timer; Viewing Stopwatch Data - Casio 5618 Operation Manual

Triggering Immediate Time Adjustment
●
After the watch is paired with a phone, you can
connect with the phone to adjust the time
setting of the watch. Perform the operation
below to connect with the paired phone and
perform an immediate time adjustment
operation.
1.
Enter the Timekeeping Mode.
Navigating Between Modes
l
2.
Move the phone close to (within one meter
of) the watch.
3. X
Hold down (D) for at least two seconds.
[CNCT] flashes to indicate that the watch
has started the connection operation.
Once the watch and phone are
connected, [OK] will appear, and then the
watch will adjust its time setting based on
information from your phone.
Trying to connect After time adjustment
Note
Connection with your phone is not
●
possible while the watch's Airplane
Mode is enabled. To connect with your
phone, disable the Airplane Mode.
Using the Watch in a Medical
l
Facility or Aircraft
The watch remains connected with
●
your phone even after time adjustment
is complete.
If time adjustment fails for some
●
reason, [ERR] will appear.

Using the Appointment Timer

The appointment timer can be linked with the
appointments of a paired phone, so the watch
can display the remaining time of the currently
ongoing appointment and/or its ending time.
Note
The appointment timer corresponds to
●
the built-in calendar of your phone's
OS and Google calendar.
The start time or end time of an
●
appointment is alerted by a beep and
on the watch display.
Up to five appointments can be sent
●
from your phone to the watch.
Operation Guide 5618
Transferring Appointments
●
Appointments can be transferred from your
phone to the watch.
While the watch is connected with your
●
phone, appointments are periodically
transferred to the watch automatically.
Make sure that the
●
watch display when you perform the
procedure below.
If is not displayed, refer to the information
e
●
at the link below.
Connecting with a Phone
l
1. Y
Tap the "EDIFICE Connected" icon.
2. Y
Perform the operation shown on the
phone screen to transfer phone
appointments to the watch.
Displaying an Appointment
●
1.
Enter the Timekeeping Mode.
Navigating Between Modes
l
2. X
Press (D).
This causes the display to change from
●
the current time to an appointment.
Each press of (B) switches between the
information as described below.
Current ongoing
appointment end time
The mode hand indicates the time
●
remaining until the currently ongoing
appointment is complete. The mode
hand points to [OVER] when there are
more than 120 minutes remaining.
Mode hand
When the remaining time of the
●
currently ongoing appointment is 10
minutes or less, the watch display
shows the remaining time, and counts it
down in one-second units.
A beeper sounds for two seconds when
●
the time setting is reached.
symbol is shown on the
e
Next appointment
start time

Viewing Stopwatch Data

This section explains how to send lap times
(up to 200 records) that are stored in watch
memory, as well as other data to your phone
for viewing with EDIFICE Connected.
Sending Stopwatch Data to a Phone
●
Use the procedure below to send data from
the watch to a phone.
While the watch is connected with your
●
phone, lap times being recorded by the
watch are periodically transferred to the
phone automatically.
Make sure that the symbol is shown on the
e
●
watch display when you perform the
procedure below.
If is not displayed, refer to the information
e
●
at the link below.
Connecting with a Phone
l
1. Y
Tap the "EDIFICE Connected" icon.
2. Y
Perform the operation shown on the
phone screen to transfer data measured
by the watch to the phone.
After data transfer is complete, a list of the
measurement data will appear on the
phone display.
Tapping a stopwatch data item displays
●
its details.
Checking a Lap Time
●
Use EDIFICE Connected to check the data
you sent to the phone.
1. Y
Tap the "EDIFICE Connected" icon.
2. Y
Perform the operation shown on the
phone screen to view the measurement
data you want.
Note
Tapping "Edit" displays a screen that
●
you can use to change the data item
title and to delete lap time data.
7