Related Manuals for Boekel UV CROSSLINKER
Summary of Contents for Boekel UV CROSSLINKER
- Page 1 BOEKEL UV CROSSLINKER Model 234100: 115VAC, 175W, 1.6A 234100-2: 230VAC, 175W, 0.8A OPERATING INSTRUCTIONS N2400340 Rev. 2 Page 1...
-
Page 2: Table Of Contents
Table of Contents Page # Safety Product Information Assembly Identification of Controls Installation Operation Technical Specifications Maintenance and Service Calibration Changing Bulbs Cleaning Contrast Adjustment Fuse Replacement Fault Diagnosis / Troubleshooting 10.0 Warranty 11.0 Service N2400340 Rev. 2 Page 2... -
Page 3: Safety
Safety WARNING: To guard against injury, basic safety precautions should be observed, including the following: Caution: Read these operating instructions fully before use and pay particular attention to sections containing this symbol. Attention: Suivre attentivement les instructions avant l’usage et prêtez une attention particulière aux sections comportant ce symbole. -
Page 4: Product Information
The Boekel UV Crosslinker is equipped with a UV-protective viewing window. This window protects users from harmful UV rays that are generated inside of the unit. Do not operate the unit with the door open or attempt to defeat the safeguards on the unit. -
Page 5: Assembly
The Boekel UV Crosslinker may be used in either Time Mode, in which the unit runs for a user- defined amount of time, or Energy Mode, in which the unit runs until a user-defined amount of energy has been accumulated. - Page 6 Figure 1 – Front View 1. LCD DISPLAY 6. UP/DOWN ARROW KEYS 2. POWER KEY 3. MODE KEY 4. RESET KEY 5. START/STOP KEY Figure 2 – Back View 7. AC POWER SOCKET 8. HEIGHT ADJUSTMENT KNOB N2400340 Rev. 2 Page 6...
-
Page 7: Installation
Operation The Boekel UV Crosslinker is equipped with a UV-protective viewing window. This window protects users from harmful UV rays that are generated inside of the unit. Do not operate the unit with the door open or attempt to defeat the safeguards on the unit. - Page 8 in Energy Mode, the display shows the accumulated energy and the calculated target time to reach that energy level. If Time Mode is selected and the “Start/Stop” key is pressed, the controller sounds a brief beep and the display shows the following for 1 second: STARTING CYCLE TIME MODE...
-
Page 9: Technical Specifications
Note: Using third-party bulbs may compromise the accuracy of the unit, as the Boekel UV Crosslinker has been programmed and calibrated to work with Boekel part numbers as listed in the following table: 254nm Bulb –... -
Page 10: Changing Bulbs
Should the unit require recalibration for any reason, please return both the unit and the bulbs being used to Boekel Scientific. See Section 11 on page 12. Changing Bulbs 8.2.1 A bulb is removed from a bulb socket with a quarter turn... -
Page 11: Cleaning
Cleaning 8.3.1 Disconnect the power cord prior to cleaning and let the unit and bulbs cool down. 8.3.2 If a spill occurs, use appropriate clean-up procedures as required for control of the materials being cleaned. 8.3.3 Use a cloth dampened with warm water to clean the outer housing. -
Page 12: Fault Diagnosis / Troubleshooting
10.0 Warranty When used in laboratory conditions and according to these operating instructions, Boekel warrants this product to be free of defective material and workmanship for a period of two years from the date of manufacture. The liability of Boekel for any defective equipment during the warranty period shall be limited to the repair of such equipment or replacement thereof with charge for parts or labor. -
Page 13: Service
Boekel product, for any reason. Decontamination Certificate must be completed, signed by the user and returned to Boekel Scientific in order to receive the RMA number. Please be sure to mark the outside of the returned goods package with the RMA number, in order to ensure prompt handling.
Need help?
Do you have a question about the UV CROSSLINKER and is the answer not in the manual?
Questions and answers