elsner elektronik R 24 V Technical Specifications And Installation Instructions
  1. Manuals
  2. Brands
  3. elsner elektronik Manuals
  4. Accessories
  5. R 24 V
  6. Technical specifications and installation instructions

elsner elektronik R 24 V Technical Specifications And Installation Instructions

Rain sensor
Hide thumbs
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

Download this manual
EN
R 24 V
Rain Sensor
Technical specifications and installation instructions
Item number 30158
Elsner Elektronik GmbH Control and Automation Engineering
Sohlengrund 16
75395 Ostelsheim
Germany
Phone +49 (0) 70 33 / 30 945-0 info@elsner-elektronik.de
Fax
+49 (0) 70 33 / 30 945-20 www.elsner-elektronik.de
Technical support: +49 (0) 70 33 / 30 945-250

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the R 24 V and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for elsner elektronik R 24 V

Summary of Contents for elsner elektronik R 24 V

  • Page 1 R 24 V Rain Sensor Technical specifications and installation instructions Item number 30158 Elsner Elektronik GmbH Control and Automation Engineering Sohlengrund 16 75395 Ostelsheim Phone +49 (0) 70 33 / 30 945-0 info@elsner-elektronik.de Germany +49 (0) 70 33 / 30 945-20 www.elsner-elektronik.de...

  • Page 2: Technical Specification

    Description Description The R 24 V rain sensor signals precipitation (rain, snow) via a 24 V DC output. Functions: • Heated precipitation sensor (1.2 watts): No error measurement with dew or mist, fast drying after the rain ends • Outlet for rain signal (24 V DC) •...
  • Page 3 Elsner Elektronik is not liable for any changes in norms and standards which may occur after publication of these operating instructions.

  • Page 4: Sensor Assembly

    Fasten the mount vertically onto the wall or pole. Fig. 4 When wall mounting: flat side on wall, crescent- Collar shaped collar upward. R 24 V rain sensor • Version: 03.03.2016 • Technical changes and errors excepted.
  • Page 5 Sun, wind and precipitation can act upon the sensors without hindrance. Fig. 8 Example use of the hinge arm mounting: Fitting to a pole with worm drive hose clips R 24 V rain sensor • Version: 03.03.2016 • Technical changes and errors excepted.
  • Page 6 Fig. 9 a+b Drill hole plan Dimensions of rear side of housing with bracket. Sub- ject to change for technical enhancement. Langloch 7,5 x 5 mm R 24 V rain sensor • Version: 03.03.2016 • Technical changes and errors excepted.
  • Page 7 2 Bottom of housing The lid of the R 24 V with the rain sensor latches into place on the lower edge to the right and left (see Fig.). Remove the lid. Proceed carefully to avoid tearing off the cable connection between the circuit board in the lower section and the rain sensor in the lid (cable with plug).

  • Page 8: Notes On Mounting And Commissioning

    The holding time is set using a potentiometer on the inside of the housing. Turning anti-clockwise reduces the holding time (minimum value 10 seconds). Turning clock- wise increases the holding time (maximum value 300 seconds). R 24 V rain sensor • Version: 03.03.2016 • Technical changes and errors excepted.

  • Page 9: Maintenance

    ATTENTION The device can be damaged if water penetrates the housing. • Do not clean with high pressure cleaners or steam jets. R 24 V rain sensor • Version: 03.03.2016 • Technical changes and errors excepted.

This manual is also suitable for:

30158

Table of Contents