Related Manuals for netvox R718NL1 Series
Summary of Contents for netvox R718NL1 Series
- Page 1 Model：R718NL1 Wireless Light Sensor and 1-Phase Current Meter Wireless Light Sensor and 1-Phase Current Meter R718NL1 User Manual...
-
Page 2: Table Of Contents
Table of Content 1. Introduction ....................................... 2 2. Appearance ....................................... 3 3. Main Features ....................................3 4. Set up Instruction ....................................4 5. Data Report ....................................... 5 6. Installation ......................................8 7. Information about Battery Passivation ............................. 9 7.1 To determine whether a battery requires activation ......................... 9 7.2 How to activate the battery ............................... -
Page 3: Introduction
1. Introduction The R718NL1 series is a Wireless Light Sensor and 1-Phase Current Meter device for Netvox ClassA type devices based on the LoRaWAN open protocol and is compatible with the LoRaWAN protocol. R718NL1 series have different measurement range for different variety of CT. -
Page 4: Appearance
Low power consumption and long battery life Note: Battery life is determined by the sensor reporting frequency and other variables, please refer to http://www.netvox.com.tw/electric/electric_calc.html On this website, users can find battery life time for varied models at different configurations. -
Page 5: Set Up Instruction
4. Set up Instruction On/Off Power on Insert batteries. (users may need a flat blade screwdriver to open) Turn on Press and hold the function key for 3 seconds till the green indicator flashes once. Turn off Press and hold the function key for 5 seconds till green indicator flashes for 20 times. (Restore to factory setting) Power off Remove Batteries. -
Page 6: Data Report
(3) If MinTime configuration less than 30 seconds, it will configure 30 seconds. (4) R718NL1 series would take about 15 seconds for the CT to sample and process the collected value, If the current changes frequently, the sampling result might be wrong. - Page 7 Example of Report configuration FPort：0x07 Bytes 1 Byte 1 Byte Var(Fix =9 Bytes) CmdID DeviceType NetvoxPayLoadData CmdID– 1 byte DeviceType– 1 byte – Device Type of Device NetvoxPayLoadData– var bytes (Max=9bytes) Device Description Device CmdID NetvoxPayLoadData Type MinTime MaxTime CurrentChange Illuminancechange Reserved ConfigReportReq...
- Page 8 Example#2 based on MinTime = 15 Minutes, MaxTime= 1 Hour, Reportable Change i.e. BatteryVoltageChange= 0.1V. MaxTime Sleeping(MinTime) sleeping sleeping sleeping Wakes up and Wakes up and Wakes up and Wakes up and Wakes up and collects data collects data collects data collects data collects data REPORT 3.6V...
-
Page 9: Installation
6. Installation This product comes with waterproof function. When using it, the back of it can be adsorbed on the iron surface, or the two ends can be fixed to the wall with screws. When installing the current transformer, separate the fire and neutral wires, and take out the fire wire separately and start the measurement according to the wiring below. -
Page 10: Information About Battery Passivation
7. Information about Battery Passivation Many of Netvox devices are powered by 3.6V ER14505 Li-SOCl2 (lithium-thionyl chloride) batteries that offer many advantages including low self-discharge rate and high energy density. However, primary lithium batteries like Li-SOCl2 batteries will form a passivation layer as a reaction between the lithium anode and thionyl chloride if they are in storage for a long time or if the storage temperature is too high. -
Page 11: Important Maintenance Instruction
8. Important Maintenance Instruction Kindly pay attention to the following in order to achieve the best maintenance of the product: • Keep the device dry. Rain, moisture, or any liquid, might contain minerals and thus corrode electronic circuits. If the device gets wet, please dry it completely.