Product Familiarisation - GMC GMBL18CH Original Instructions Manual

Use batteries correctly
• Only charge batteries using the charger provided. Only use batteries provided with this
power tool, or others recommended by the supplier. Keep batteries clean; foreign objects or
dirt may cause a short. Allow batteries to cool for 15 minutes after charging or heavy use.
Failure to follow these instructions may cause overheating or fire.
WARNING: Li-Ion batteries, if incorrectly used, stored or charged are a fire, burn and
explosion hazard.
• Keep the battery out of reach of children
• Only charge Li-Ion batteries using the charger provided or designed specifically for your
product
• Only use Li-Ion batteries provided with a product or specifically designed to be
GB
compatible
• Allow batteries to cool for 15 minutes after charging or heavy use. Failure to follow
these instructions may cause overheating or fire
• When not in use batteries should be stored at room temperature (approximately 20˚C)
• Ensure that battery contacts cannot accidentally short in storage. Keep batteries clean;
foreign objects or dirt may cause a short. Keep away from other metal objects, for
example paperclips, coins, keys, nails and screws
• Under abusive conditions, liquid may be ejected from the battery. This liquid may cause
skin irritation or burns. Avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, seek medical help
• Do not open, disassemble, crush, heat above 60°C or incinerate. Do not dispose of in
fire or similar

Product Familiarisation

1. Keyless Chuck
2. Torque Selector
3. Mode Selector
4. Gear Selector
5. Motor Vents
6. Forward/Reverse Switch
7. Hand Grip
8. Charge Indicator (not visible)
9. Battery
10. Bit Holder
11. Battery Release
12. Belt Clip
13. Speed Control Trigger Switch
14. Work Light LED
15. Battery Charger
16. Green LED
17. Red LED
Accessories (not shown): Soft carry case
Note: This manual may be supplied with different package configurations and supplied
accessories may vary.
Intended Use
• Battery-operated drill with screwdriver, drill and impact drill functions suitable for
medium duty drilling and driving tasks. Includes hammer/impact function for light
masonry drilling.
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing
or damaged, have such parts replaced before attempting to use this tool
Before Use
Removing a battery
• To remove the Battery (9) from the drill, press the Battery Release (11), then slide the
Battery off towards the front of the drill
WARNING: DO NOT try to remove the Battery without pressing the Battery Release button.
The drill or Battery could be damaged.
Fitting a battery
1. To fit a charged battery, slide it on to the battery slot below the Hand Grip (7) of the drill
until it clicks and locks into position
Note: Make sure the Battery and drill are lined up correctly. If the Battery does not slide
into the drill easily, don't force it. Instead, slide the Battery out of the drill again, check the
top of Battery and the drill battery slot are clean and undamaged and that the contacts are
not bent.
Setting up the battery charger
1. If fitted, remove any battery from the Battery Charger (15)
2. Insert the Battery Charger mains plug into a suitable mains socket
Note: The Green LED (16) on the Battery Charger will blink to indicate that the Battery
Charger is ready to charge the battery.
WARNING: ONLY use this charger to charge the supplied battery or additional purchased
batteries that are specifically designed for this tool.
WARNING: The charger is designed for indoor use only, and MUST NOT be used in
damp or wet conditions.
Charging the battery
WARNING: Failure to follow the correct procedure when charging batteries will result in
permanent damage.
Note: Normal charging time is 80 minutes for a recently discharged 4Ah battery. However, if
the Battery (9) has been left in a discharged state for some time, it may take up to 2 hours
to charge.
1. Slide a fully or partially discharged Battery onto the Battery Charger (15)
Note: Make sure the Battery and Battery Charger are lined up correctly. If the Battery does
not slide onto the Battery Charger easily, don't force it. Instead, remove the Battery, check
the top of Battery and the Battery Charger slot are clean and undamaged and that the
contacts are not bent.
2. Once charging commences, the Red LED (17) will illuminate
3. When the Battery is fully charged, the Green LED (16) will be illuminated
Battery Charge Level: The Battery has a built-in Charge Indicator (8) (Fig. I). Pressing on
the button to the right will indicate the charge level. The right LED indicates a high charge
level and the left a low charge level that will mean the battery pack will require charging
soon.
IMPORTANT: When a low charge level is indicated be aware the tool may stop operating
while using the tool. In some instances this may be dangerous. It is recommended to
always ensure the battery pack has a good charge level.
8