Advertisement
Quick Links
Advertisement
Related Manuals for Renaissance Fireplaces Rumford 1000
Summary of Contents for Renaissance Fireplaces Rumford 1000
- Page 1 RUMFORD 1000 / 1000CD / 1000H...
-
Page 2: Table Of Contents
They incorporate technology with elegance, allowing you to enjoy an open fire without compromising environmental quality. We at Renaissance Fireplaces™ congratulate you on your choice of the Rumford 1000, 1000CD or 1000H and are confident that you have purchased a fireplace that burns clean, without compromise. Sincerely,... - Page 3 If for any reason, you need to dismantle the guillotine system, carefully follow the instructions below. It can be done by one person but it is easier if there is an additional person to help. Here is the list of tools you will need: "...
-
Page 4: Removing The Firescreen And Its Rails
Step 2 EMOVING THE IRESCREEN AND • Using a " Allen key, unscrew the left AILS firescreen rail. • Start with the top screw, then unscrew Step 1 the lower one. The screws are holding • Renaissance Rumford 1000CD the rails in place, but there are also fireplaces, please jump... - Page 5 Step 3 Step 4 • Get a hold of the firescreen with both • Using a " Allen key, unscrew the hands and bring it down. right firescreen rail. • Slide the firescreen towards the left to • Start with the top screw, then unscrew disengage the right side from the right the lower one.
-
Page 6: Disabling The Guillotine Counterweights
Step 5 ISABLING THE UILLOTINE • Remove both firescreen rails from the OUNTERWEIGHTS guillotine bay. Step 6 • Remove the counterweight cover on each side. They are located at the bottom of the guillotine bay on the far left and far right. There are two screws holding each cover. - Page 7 Step 9 Step 10 • At the bottom outside corners of the • Place the wood piece vertically under guillotine door frame, on each side of the door to hold it in place. To lift the the door there is a threaded oval door high enough to insert the 2x4, you connector.
- Page 8 Step 11 Step 12 Be very careful not to knock the 2"x4" Be very careful not to knock the 2"x4" holding the door. holding the door. • Remove the left threaded connector • Get a good hold of one of the cables, and cable from the guillotine frame and wear gloves to prevent getting cut by without letting go of the connector,...
-
Page 9: Removing The Glass Door
Step 14 EMOVING THE LASS • Using the glass door handles, unlock the glass door and open it. Step 13 • Either have someone to hold the glass • Get a good hold of the door. door or place a cushion under it to hold •... -
Page 10: Removing The Guillotine Frame
Step 16 EMOVING THE UILLOTINE • Using a small ratchet with a " long RAME (2" min.) magnetic socket, remove the bottom nut on both sides. They are Step 15 behind the bottom holes you have uncovered by removing the round caps. •... - Page 11 Step 17 Step 18 • Remove all eight nuts located at the • Remove all four nuts on the right side. top of the guillotine frame. They are behind the holes you have uncovered by removing the round caps. • Pull the right side of the guillotine frame forward.
-
Page 12: Removing The Guillotine Counterweights
Step 19 EMOVING THE UILLOTINE • Remove all four nuts on the left side. OUNTERWEIGHTS • While holding the stainless steel gasket at the top, pull the left side of the Step 20 guillotine frame forward and remove it. • Grab a hold of one of the cables Be careful not to damage the stainless attached to the counterweights, lift it... -
Page 13: Removing The Guide Rail System And Pulleys
Step 22 EMOVING THE UIDE • Using a small ratchet with a " socket YSTEM AND ULLEYS or a " wrench, remove the four nuts holding the pulley support in place at Step 21 the very top of the left guide rail system. -
Page 14: Changing The Pulleys
Step 24 HANGING THE ULLEYS • Repeat Removing Guillotine Counterweights Step 23 • Step 20 through Changing the Pulleys • Take a marker and make a line along the pulleys before removing them. The • Step 23 for the other side. alignment of the pulleys is critical to You can now change the pulleys. - Page 15 RR1000-CD-H - guillotine - 2010-04...
Need help?
Do you have a question about the Rumford 1000 and is the answer not in the manual?
Questions and answers