Advertisement
STEP 1: Connecting to Lorex Home
Connect to the camera using the free Lorex Home app on your
iPhone® or Android™ phone.
To install the camera:
1. Attach the included antenna to the back of the camera.
2. Using a Phillips screwdriver (not included), remove the panel
on the bottom of the camera.
3. Use the included power adapter to connect your camera to a
nearby outlet.
4. Download and install the free Lorex Home app
from the App Store or Google Play Store.
5. Tap the Lorex Home icon to launch the
app. Tap Sign up, then follow the on screen
prompts to create an account. Record your
account details below and store in a secure
location:
Email:
Account Password:
6. Open the compartment on the bottom of the camera using a
Phillips head screwdriver to reveal the status LEDs.
7. Once the status LED on the camera is flashing green and the
startup chime sounds, tap + in the Lorex Home app.
8. Scan the QR code on the
bottom of the camera
using your mobile device's
camera.
NOTE:
If your mobile
device cannot scan the QR
Device ID: × × × × × × ××
code, tap Manually enter
Device ID.
9. Create a secure password for the camera. Record your
camera password below:
Camera Password:
10. Select your Wi-Fi network from the list, then enter the
password to connect your camera to the Internet.
11. Once the status LED on the camera is solid green, tap Next to
add the camera to your Lorex Home account.
12. Set a name for the camera and configure date & time
preferences, then tap Complete to finish the setup.
13. Replace the bottom panel of the camera.
LNBW421_QSG_EN_R1.indd 2
LNBW421_QSG_EN_R1.indd 2
STEP 2: Installing the Camera
Choose a mounting location and install your camera. The camera
can be installed on a wall or ceiling.
Before Installing the Camera
• Review the Installation Tips section on the other side of the guide to
help you choose an ideal mounting location.
• Decide whether to run the cables through
the wall / ceiling (drilling required) or along
the wall / ceiling. If you run the cables
along the wall / ceiling, you must run the
cable through the cable notch on the base.
This will keep the camera base flush to the
surface when mounted.
To install the camera:
1. Disconnect the power adapter before mounting.
2. Use the included mounting template to mark holes for the
mounting screws.
3. Drill holes where marked. Insert the drywall anchors if you are
mounting the camera onto drywall.
4. Secure the camera
Figure 1
base to the wall using
Mounting surface
the included screws.
Make sure all screws
Mounting screws (×3)
are fastened tightly
(see Figure 1).
5. Using a Phillips
screwdriver (not
included) loosen the
adjustment screw
slightly. Position the
Figure 2
camera as needed,
then tighten the
adjustment screw to
secure the camera
in place (see Figure
2).
6. Reconnect the
included power
adapter to the camera
Adjustment screw
cable.
7. Remove the vinyl cover on the camera lens to finish the
installation.
Using the Weather Resistant Cap
O-Ring
Camera Ethernet Connector
1. Fit the O-ring around the camera Ethernet connector.
2. Connect the cable to the camera Ethernet connector.
3. Twist the barrel securely onto the camera Ethernet connector.
The O-ring becomes compressed when the seal is properly
tight.
Cable Notch
4. Twist the end cap securely onto the barrel.
LED Indicators
The LED indicators under the panel on the bottom of the camera
will glow different colors to indicate different states. See the table
below:
LED Behavior
(steady)
(flashing)
(flashing rapidly)
(steady)
(flashing)
Drywall anchors (×3)
(flashing rapidly)
(flashing)
Resetting the Camera
Reset the camera password and restore default settings.
To reset the camera:
1. Using a Phillips screwdriver
(not included), remove the
panel on the bottom of the
camera.
2. Hold the RESET button (see
Figure 3) for approximately
10 seconds until the LED
flashes red.
3. Replace the panel.
4. Repeat the setup procedure
for the camera.
(Optional)
Barrel
End Cap
Meaning
Camera is starting up
Camera is disconnected from network
Camera failed to start up
Camera is fully set up and operating normally
Camera start-up complete, awaiting Wi-Fi
configuration
Wi-Fi configuration in progress
Firmware upgrade in progress
Figure 3
Reset
button
LNBW421_QSG_EN_R1
2019-11-28 3:28:24 PM
2019-11-28 3:28:24 PM
Advertisement
