Table of Contents
Advertisement
Quick Links
INGICS
Guide
Ver.01
iGS01S is a bridge to connect the local BLE devices, sensors, or beacons to the internet by the WiFi.
Through an easy web UI interface, one can configure the internet connection to a general cloud server, like
TCP, HTTP(S), or MQTT. Management through the cloud to the BLE devices becomes simple through
iGS01S. This guide is to help the user to figure out how to operate and configure the iGS01S.
Contents
Contents
Overview
Inside the box
WiFi
BLE
Input and Output
Multi-function button
WPS
Reset to Default
Firmware Upgrade
LEDs
Create Connection
Web User Interface
Wi-Fi
Simple AP
Station
Network
AP Client Setting
AP Server Setting
Applications
M2M TCP Server
M2M TCP Client
HTTP Client
Request Interval
Throttle Control
MQTT Client
MQTTS
Advanced
BLE Filter
RSSI
Payload Whitelist
Device Key/Certification Update
System
NTP setting
Revision History
I NGICS TECHNOLOGY CO., LTD. • JK.FAN@INGICS.COM • WWW.INGICS.COM
T ECHNOLOGY
BLE_WiFi Gateway
iGS01S User Guide
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ingics iGS01S
Summary of Contents for Ingics iGS01S
- Page 1 Ver.01 iGS01S is a bridge to connect the local BLE devices, sensors, or beacons to the internet by the WiFi. Through an easy web UI interface, one can configure the internet connection to a general cloud server, like TCP, HTTP(S), or MQTT. Management through the cloud to the BLE devices becomes simple through ...
-
Page 2: Inside The Box
Inside the box There are one iGS01S unit, one 1M USB cable, and one 2dBi dipole antenna included in one full shipping package. iGS01S is powered by a standard micro-USB cable, rated at 5V&500mA. You can power this device with a standard smartphone charger or the USB port of any host device that can support ... -
Page 3: Input And Output
Optional timestamp when NTP is enabled Input and Output Multi-function button One multi-function button is on one side of the iGS01S as the figure showed. It is used to act WPS, reset to default settings, and OTA (over-the-air FW upgrade). Below is how it ... -
Page 4: Reset To Default
WPS to connect to your Access Point. First press the WPS button on your Access Point, when it ready, then press the WPS button on the iGS01S device( the WPS button need to be pressed for over 1 sec) to join it. ... -
Page 5: Create Connection
When In Station mode, the IP address of the iGS01S is assigned by the the other AP. To get into the web UI, you have to find the assigned IP address. ... - Page 6 IP address for iGS01S, the DHCP client should be disabled. Once disabled, user should assign the IP, Netmask, Gateway, and/or DNS server. AP Server Setting 6 I NGICS TECHNOLOGY CO., LTD. • JK.FAN@INGICS.COM • WWW.INGICS.COM ...
- Page 7 192.168.0.1, the DHCP clients associated to iGS01S AP will be 192.168.0.X. Applications M2M TCP Server iGS01S is a TCP server with fixed IP address 192.168.10.1. The default port is 8080 and user can also assign the port. M2M TCP Client ...
-
Page 8: Throttle Control
Throttle Control If user select to enable throttle control, iGS01S will keep the last record for each TAG/Beacon ID in the given interval(request interval). In this way, one can reduce the upload connections ... - Page 9 User can upload certification and key here. This is used by MQTTS. AWS-IOT users must upload the certificate and private key here to publish data to AWS-IOT. 9 I NGICS TECHNOLOGY CO., LTD. • JK.FAN@INGICS.COM • WWW.INGICS.COM ...
-
Page 10: Ntp Setting
Revision History DATE REVISION CHANGES Apr 16, 2018 01 Initial release 10 I NGICS TECHNOLOGY CO., LTD. • JK.FAN@INGICS.COM • WWW.INGICS.COM ... - Page 11 20 centimètre de toute personne et doit pas être co-située ni fonctionner en conjonction avec une autre antenne ou émetteur. NCC 警語 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者 均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信； 經發現有 干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、 科學及醫療用電波輻射性電 機設備之干擾 電磁波曝露量MPE標準值1mW/cm2，送測產品實測值 0.0103mW/cm2。 11 I NGICS TECHNOLOGY CO., LTD. • JK.FAN@INGICS.COM • WWW.INGICS.COM ...
- Page 12 Ver.01 BLE to WiFi Beacon Gateway iGS01S is a BLE to WiFi gateway and bridge. The gateway reads iBeacon and Eddystone like beacon or customized Tag( w/ sensor) format and sends to local TCP server or internet HTTP/MQTT server. User can configure the transmit period and server information through a simple web UI. ...
-
Page 13: Specification
-40º to 85º Celsius Voltage Ripple +-5% Recommendable Operation Condition Operating Temperature -20º to 60º Celsius Humidity Max 95%, Non condensing, relative humidity VDD +5 Volt +- 5% 2 I NGICS TECHNOLOGY CO., LTD. • JK.FAN@INGICS.COM • WWW.INGICS.COM ... - Page 14 +- 4 dB Receiver Sensibility -96 dBm @250kbps, 0.1% BER -90 dBm @1Mbps, 0.1 %BER Maximum Received Signal 0dBm Strength at <0.1% PER Frequency Deviation +-250 kHz @BLE 3 I NGICS TECHNOLOGY CO., LTD. • JK.FAN@INGICS.COM • WWW.INGICS.COM ...
- Page 15 Dimensions L x W x H (mm) 55 x 41 x 18 (not including dipole antenna) Packing Each iGS01S has it’s accessory including a dipole antenna and micro-USB cable. Two packing boxes(size: 11cmX5.5cmx6.5cm) contains 5 units of iGS01S and accessories. 5X...
- Page 16 20 centimètre de toute personne et doit pas être co-située ni fonctionner en conjonction avec une autre antenne ou émetteur. NCC 警語 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者 均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信； 經發現有 干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、 科學及醫療用電波輻射性電 機設備之干擾 電磁波曝露量MPE標準值1mW/cm2，送測產品實測值 0.0106mW/cm 。 5 I NGICS TECHNOLOGY CO., LTD. • JK.FAN@INGICS.COM • WWW.INGICS.COM ...
Need help?
Do you have a question about the iGS01S and is the answer not in the manual?
Questions and answers