Paradox Spectra 1641 Installer's Manual

The 1641 LCD Keypad includes a programmable 32-character LCD screen, zone input and a PGM output as well as supporting the use of the
Paradox Memory Key. All of the LCD keypad's features and options can only be accessed through the keypad's programming mode. During
the keypad's power up, press and hold the [
[1] Labels
This feature allows you to program some of the messages that appear on the keypad's LCD screen. In step 3 of "Entering Keypad Programming
Mode" described in the shaded box above, select option [1]. The keypad will prompt you to enter a 3-digit section. Each section from [101] to
[135] represents a specific message. Enter the 3-digit section that corresponds to the message you wish to change.
[101] to [116]= Zone 1 to Zone 16
[133] = Partition 1
[134] = Partition 2
[135] = Keypad Name (default: "Spectra Family")
Key
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[0]
[2] Options
In step 3 of "Entering Keypad Programming Mode", select option [2]. You will now be able to enable or disable the keypad's options as shown
in table 2. Press the corresponding keys until all desired options are set, then press [
Key Description
[1] Keypad Zone Sending
[2] Keypad Zone Requires 1K EOL Resistor
[3] Keypad Zone Set to
[4] On-Board Keypad Tamper Supervision
[5] Status LED Follows Arming Status of
[6] Multiple Zone Display (status of several zones on one screen without zone label)
[7] Scrolling Zone Display (each screen displays zone label and status of one zone)
[8] For Future Use
1641 LCD KEYPAD V1.0 - INSTALLER'S GUIDE
] key to set the LCD screen and the Keypad Code to default.
CLEAR
Entering Keypad Programming Mode
STEP 1:Press and hold the [0] key for two seconds.
STEP 2:Enter the [
KEYPAD CODE
STEP 3:Press the key corresponding to the desired option or use the arrow keys to
scroll through the available options and press [
[1] = Labels
[2] = Options
[3] = Keypad Code
[UC] Mode
X1 X2 X3 X4
A B C 1
D E F 2
G H I 3
J K L 4
M N O 5
P Q R 6
S T U 7
V W X 8
space Y Z 9
@ ! = 0
]. Default:000000
ENTER
[4] = Keypad PGM
[5] = Read Key
[6] = Write Key
Table 1: Character Sets
[LC] Mode
X1 X2 X3
a b c
d e f
g h i
j k l
m n o
p q r
s t u
v w x
space y z
' { }
Table 2: Keypad Options
OFF
! ! ! ! Disabled
! ! ! ! No (default)
! ! ! ! Keypad Zone 1 (default)
! ! ! ! Disabled (default)
! ! ! ! Partition 1 (default)
! ! ! ! Disabled (default)
! ! ! ! Disabled (only if [6] = ON)
! ! ! ! N/A
].
[SP] Mode
X4 X1 X2 X3
- Û Ù Ú
& û ù ú
* Ò Ó o
( ò ó ö
) Ê È É
[ ê è é
] Å Ä å
> à á ä
< a Î Ì
0 ï i Ñ
].
ENTER
X4
Ü
Ô
ô
¿
Ë
ë
â
A
Í
ñ
ON
! ! ! ! Enabled (default)
! ! ! ! Yes
! ! ! ! Keypad Zone 2
! ! ! ! Enabled
! ! ! ! Partition 2
! ! ! ! Enabled
! ! ! ! Enabled (default)
! ! ! ! N/A