Related Manuals for Raven AccuBoom 117-1001-076
Summary of Contents for Raven AccuBoom 117-1001-076
- Page 1 GVM Predator and Prowler AccuBoom Installation Manual Manual No. 016-1001-072 Rev B. 01/17 E28642 Copyright 2017...
- Page 2 GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.
-
Page 3: Table Of Contents
Table of Contents Chapter 1 Important Safety Information ................1 Important Safety Information ..................... 1 Instructions for Wire Routing ..................... 1 Instructions for Hose Routing ....................3 Chapter 2 Introduction......................5 Introduction ..........................5 Recommendations ................................. 5 Tools Needed ................................... 5 Preparing for Installation .............................. - Page 4 Table of Contents GVM Predator and Prowler AccuBoom Installation Manual...
-
Page 5: Chapter 1 Important Safety Information
AccuBoom™ system. • Follow all safety information presented within this manual. • If you require assistance with any portion of the installation or service of your Raven equipment, contact your local Raven dealer for support. • Follow all safety labels affixed to the AccuBoom system components. Be sure to keep safety labels in good condition and replace any missing or damaged labels. - Page 6 HAPTER Harness should not contact or be attached to: • Lines and hoses with high vibration forces or pressure spikes • Lines and hoses carrying hot fluids beyond harness component specifications Avoid contact with any sharp edge or abrading surfaces such as, but not limited to: •...
-
Page 7: Instructions For Hose Routing
IMPORTANT SAFETY INFORMATION Protect harnesses from: • Foreign objects such as rocks that may fall or be thrown by the unit • Buildup of dirt, mud, snow, ice, submersion in water and oil • Tree limbs, brush and debris • Damage where service personnel or operators might step or use as a grab bar •... - Page 8 HAPTER • Drive shafts, universal joints and hitches (i.e. 3-point hitch) • Pulleys, gears, sprockets • Deflection and backlash of belts and chains • Adjustment zones of adjustable brackets • Changes of position in steering and suspension systems • Moving linkages, cylinders, articulation joints, attachments •...
-
Page 9: Chapter 2 Introduction
C H A P T E R 2 INTRODUCTION Congratulations on your purchase of the Raven AccuBoom system! This system is designed to provide accurate and cost-efficient application control by avoiding no-spray zones and eliminating wasteful overlaps. This manual applies to the following machines. For future reference, write your serial number in the space below. -
Page 10: Preparing For Installation
This section contains a list of the components that are included in the AccuBoom kit. Before beginning the AccuBoom installation, compare the items in the AccuBoom kit with the components on this list. If you have questions about the kit, contact your local Raven dealer. TABLE 1. AccuBoom Installation Kit (P/N 117-1001-076) -
Page 11: Install The Accuboom Node
A CCUBOOM INSTALLATION CHAPTER C H A P T E R 3 The instructions in this manual are designed to assist in the proper installation of the AccuBoom system on GVM Predator and Prowler series sprayers. Refer to your field computer’s Installation & Operation Manual for instructions on setting up the software and using the AccuBoom system. -
Page 12: Install The Accuboom Harness Cable
HAPTER INSTALL THE ACCUBOOM HARNESS CABLE INSTALL THE POWER CONNECTION FIGURE 2. AccuBoom Harness Power Connection 1. Locate the 4-pin weather pack connector in the node enclosure. 2. Remove the dust cap from the weatherpack connector. 3. Connect the weatherpack connector to the power connection on the AccuBoom harness cable (P/N 115-1001- 037). -
Page 13: Connect The Harness To The Accuboom Valve
ACCUBOOM INSTALLATION FIGURE 4. AccuBoom Cable Routing 5. Route the AccuBoom harness valve connections through the hole in the bottom of the node enclosure. CONNECT THE HARNESS TO THE ACCUBOOM VALVE FIGURE 5. AccuBoom Harness Cable Valve Connections 1. Locate the 3-pin weatherpack boom valve connections on the machine. 2. - Page 14 HAPTER GVM Predator and Prowler AccuBoom Installation Manual...
-
Page 15: Section Mapping Setup
S ECTION MAPPING SETUP CHAPTER C H A P T E R 4 This section contains section mapping settings that are used to program the AccuBoom controller. Refer to the controller’s Installation & Operation Manual and the appropriate section in this chapter for programming instructions and section mapping settings for your specific field computer. - Page 16 HAPTER GVM Predator and Prowler AccuBoom Installation Manual...
-
Page 17: Troubleshooting
AccuBoom system. NOTE: If the LEDs are not displayed as outlined in the figure below, check the CAN connections and the control cable connections on the node. If the issue persists, contact your local Raven dealer for additional technical support. NOTE: All boom switches must remain in the On position while AccuBoom control is in operation. - Page 18 HAPTER GVM Predator and Prowler AccuBoom Installation Manual...
- Page 19 Index AccuBoom Installation Harness Cable 10 Connecting AccuBoom Valve Installing the CAN Connections Installing the Power Connection Installing the AccuBoom Node 9 Introduction AccuBoom Kit Contents Point of Reference Preparing for Installation Recommendations Tools Needed Kit Contents Section Mapping Setup Envizio Pro Viper Pro Troubleshooting...
- Page 20 Index GVM Predator and Prowler AccuBoom Installation Manual...
- Page 21 How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval.
- Page 22 Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility. The Return...
Need help?
Do you have a question about the AccuBoom 117-1001-076 and is the answer not in the manual?
Questions and answers