Installation; General; Installing 4" (102 Mm) Legs - Hatco FLAV-R-SAVOR FS2HAS Series Installation And Operating Manual

English

General

The Flav-R-Savor Heated Air Curtain Cabinets are shipped
®
with most components installed and ready for operation. The
following installation instructions must be performed before
plugging in and operating the cabinet.
WARNING
ELECTRIC SHOCK HAzARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Units supplied without an electrical plug require field
installation of proper plug. Plug must be properly
grounded and of
configuration for electrical specifications of unit.
Contact a qualified electrician to determine and install
proper electrical plug.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
FIRE HAzARD: Locate unit a minimum of 1" (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
Locate unit at proper counter height in an area that is
convenient for use. Location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support weight of unit and contents.
NOTICE
Do not locate unit in area with excessive air movement
around unit. Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
1. Remove the unit from the carton.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
ImPORTANT OWNER INFORmATION section for details.
2. Remove tape and protective film from all surfaces of unit.
3. Place the unit in the desired location. This step requires at
least two people.
• Locate the unit in an area where the ambient air
temperature is constant and a minimum of 70°F (21°C).
Avoid areas that may be subject to active air movements
or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
• make sure the unit is at the proper counter height in an
area convenient for use.
• make sure the countertop is level and strong enough to
support the weight of the unit and food product.
• make sure all the feet on the bottom of the unit are
positioned securely on the countertop.
4. Seal the unit to the countertop using an NSF-approved
sealant or install the included 4" (102 mm) legs. Refer to
the "Installing the 4" (102 mm) Legs" procedure in this
section.
Form No. FS2HACm-0815
correct voltage, size,
CAUTION
5. Install any options or accessories that came with the unit.
Refer to the OPTIONS AND ACCESSORIES section for
details.
6. Plug the unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. See the
SPECIFICATIONS section for details.

Installing 4" (102 mm) Legs

Some units may be supplied with 4" (102 mm) legs. Use the
following procedure to install the legs.
The National Sanitation Foundation (NSF) requires that
units over 36" (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
and installation surface. If unit cannot be sealed at the point of
use, 4" (102 mm) legs are included to allow for proper
cleaning access below unit.
Do not lay unit on the side with the control panel. Damage
to unit could occur.
NOTE: Additional help may be needed to maneuver the unit to
the proper position for installing legs.
1. Carefully position the unit with the control panel facing up.
This step requires at least two people.
2. Attach the 4" (102 mm) legs by turning the legs clockwise
into one of the threaded holes in each of the four corners
on the bottom of the unit. Hand-tighten until snug. Do not
over-tighten.
Shorten
Lengthen
Adjustable tip for leveling.
3. Position the unit upright and move it to the desired
operating location. This step requires at least two people.
NOTE: The feet on the 4" (102 mm) legs are adjustable for
leveling the unit. Use an adjustable wrench to make
leveling adjustments once the unit is placed in its final
position.
7

INSTALLATION

CAUTION
NOTICE
Installing the Legs