Subscribe to Our Youtube Channel
Related Manuals for Adkins Studio Large Format Clam
Summary of Contents for Adkins Studio Large Format Clam
- Page 1 Studio Large Format Clam Operators Handbook ©2015 a.adkins and sons limited. all rights reserved...
- Page 2 Preface Dear User Welcome to the growing group of Studio Large Format Clam Press users. The product you have purchased has been carefully designed and manufactured to ensure that you, the user, will gain the maximum benefit. All A. Adkins & Sons Limited products are specifically designed to ensure ease of use with particular attention to safety requirements.
-
Page 3: Table Of Contents
Installing the machine Electrical requirements Adjusting the pressure How to operate the Studio Large Format Clam Press Starting with the Studio Large Format Clam Press Working with heat transfer materials Pressing pad assembly Shutting down the machine Maintenance of the Machine... -
Page 4: Introduction Studio Large Format
Format Clam Press Specifications of the Studio Large Format Clam Press The Studio Large Format Clam Press is a manually operated heat press for transfer printing and material fusing. It is ideal for medium volume production. The work area is 100 x 50 cms (39.5 x 19.5 ins). -
Page 5: Safety
If required, our customer service team can arrange maintenance service. The Studio Large Format Clam Press meets the European Legislation standard. Under normal conditions accidents are rare. However listed below are some practical points to ensure your safety. -
Page 6: Installation
Installation Transport instructions The machine comes to you either shrink-wrapped or in a box. If you have to transport the machine at any time it is recommended that you use a similar box and packing method. Please let the machine cool down and lower the handle to the locked position. -
Page 7: Adjusting The Pressure
Replacement of the mains cable must be done by a competent service engineer. HEATING ELEMENT The heating element fitted to the Studio Large Format Clam Press is rated at 7 kW. Never connect to any outlet or power supply having a different voltage/frequency from that on the machine data plate. -
Page 8: How To Operate The Studio Large
3.1.2 Turn on the Studio Large Format Clam Press; the on/off switch is on the back of the machine. Set the machine controls as necessary. See instructions for Adjusting the pressure page 4 and Operation of Control Units page 11. -
Page 9: Pressing Pad Assembly
Working with Heat Transfer Materials (cont.) 3.2.5 When the required time interval has elapsed the alarm will sound and the press should be opened by lifting the handle up until it locks into position. Unload the garment from the table of the machine taking care not to touch the heat plate to avoid risk of burns. -
Page 10: Maintenance Of The Machine
Maintenance of the Machine Daily Maintenance For good press results it is important to keep the press surfaces clean. Wipe the surface of the heat plate with a dry cloth before use when the plate is cold. Periodic Maintenance Put a few drops of oil onto the various pivot pins and the pressure adjusting screw every three months. -
Page 11: Machine Drawings And Diagrams
Machine Drawings Diagrams On the following pages are the schematic diagrams for the Studio Large Format Clam Press. General Layout………………………….…... Page 9 Exploded diagram and parts list…………... Page 10 Control unit operation……………………... Page 11 General electrical diagram………….……... Page 12 Detailed electrical diagram……….………... Page 13 Page 8... -
Page 12: General Layout
5.1 Machine General Layout ON/OFF SWITCH MAIN ISOLATOR REAR SWITCH VIEW TIME AND TEMPERATURE PRESSURE CONTROLLERS ADJUSTING HAND WHEELS HEAT PLATE MACHINE OPERATING HANDLE TABLE Page 9... -
Page 13: Exploded Diagram And Parts List
5.2 Exploded Diagram and Parts List REAR VIEW No. Description Qty. Part No. 20 Rear Electrical Box Cover 1 LFCL18 21 Fixed Mounting Plate 1 LFCL19 Fabricated Frame 1 LFCL1 Table 1 LFCL2 22 Electrical Box Back Plate 1 LFCL20 Cast Heat Plate 1 LFCL3 23 Retaining Collars... -
Page 14: Control Unit Operation
5.3 Operation Of Control Units, Setting Temperature and Time (The press must always be in the open position before the controller is set) Setting Temperature Switch on machine. HOLD HOLD STOP STOP °C °C Press 'UP' and 'DOWN' buttons to change temperature values. -
Page 15: General Electrical Diagram
5.4 General Electrical Diagram Page 12... -
Page 16: Detailed Electrical Diagram
5.5 Detailed Electrical Diagram Page 13... -
Page 17: Design Change
Design Change With the policy of constant improvement and/or modification to meet changing conditions, the right is reserved to change the design and/or specifications at any time without prior notification, and therefore specifications may vary and not be in accordance with this manual. Page 14... -
Page 18: Guarantee (Limited Warranty)
“as is”. A. Adkins & Sons Limited does not warrant that the functions of the press will meet the customer’s requirements or expectations. -
Page 19: Declaration Of Conformity
BS EN ISO 61000-6-2:2005 - EMC Immunity. Manufacturer's Name: A. Adkins & Sons Limited Manufacturer's Address: High Cross, 18 Lancaster Road, Hinckley, Leicester, LE10 0AW, United Kingdom. Type of Equipment: Studio Large Format Clam Heat Press ..................Model Number: ..................Serial Number: ..................Year of Manufacture: I, the undersigned, hereby declare that the equipment specified above conforms to the above directives and standards.
Need help?
Do you have a question about the Studio Large Format Clam and is the answer not in the manual?
Questions and answers