SunSetter Platinum Plus Replacement Instructions Manual
SunSetter Platinum Plus Replacement Instructions Manual

SunSetter Platinum Plus Replacement Instructions Manual

Semi-cassette awning fabric replacement

Advertisement

e-mail contactus@sunsetter.com, or Call Toll Free 800-670-7071 • Fax 877-224-4944
Tools Needed: Step Ladders, #2 Phillips Screwdriver and 6mm Allen wrench.
Parts Supplied: Fabric and Valance.
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN PERSONAL INJURY!! PLEASE
READ THESE INSTRUCTIONS IN ITS ENTIRETY BEFORE ATTEMPTING TO COMPLETE THIS PROCESS.
PLEASE NOTE THAT LEFT AND RIGHT REFERENCES ARE AS YOU ARE FACING THE HOUSE.
Before beginning, please familiarize yourself with the Awning and components in Figure 1.
Figure 1
Awning must be
open all the way
until Fabric sags
1. Open the Awning to the fully extended position.
2. Unplug the power cord from the wall outlet.
3. Using the Manual Crank Wand, continue to unroll the
Fabric until you expose the Fabric Slot in the Roller Bar
and create maximum slack in the Fabric.
a. The Lateral Arms will be fully extended and the Fabric
will lay loosely over the fully extended Arms.
b. The Fabric Slot in the Roller Bar will be facing forward,
toward the opening in the Housing. See Fig 2.
For Technical Support visit us at http://ownerscorner.sunsetter.com,
Platinum Plus Semi-Cassette Awning

Fabric Replacement Instructions

* Helpers Needed *
Lateral Arm
©SunSetter Products, 184 Charles Street, Malden, MA 02148
Motor inside assembly
Manual
Override
Figure 2
Fabric Slot in Roller
Bar exposed and,
facing forward.
Fabric shown with
maximum slack.
Roller Bracket
End Plate Assembly
Plastic Roller
Bracket Caps
Manual
Crank Wand

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Platinum Plus and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SunSetter Platinum Plus

  • Page 1 For Technical Support visit us at http://ownerscorner.sunsetter.com, e-mail contactus@sunsetter.com, or Call Toll Free 800-670-7071 • Fax 877-224-4944 Platinum Plus Semi-Cassette Awning Fabric Replacement Instructions * Helpers Needed * Tools Needed: Step Ladders, #2 Phillips Screwdriver and 6mm Allen wrench. Parts Supplied: Fabric and Valance.
  • Page 2 For PRO Model with Motor on LEFT side, go to Step 21, next page. 4. Remove the Plastic Roller Bracket Caps from the 10. With your helper, pull the old Fabric out of the opposite end of the Motor side of the Semi- Roller Bar and Front Bar slots AT THE SAME TIME.
  • Page 3 For PRO Model with Motor on LEFT side, proceed below: 21. Remove the Plastic Roller Bracket Cap from the 26. ON THE OPPOSITE SIDE OF THE MOTOR, remove right side of the Awning (opposite end of the the three Phillips screws from the End Plate of the Motor).
  • Page 4 34. Attach the Roller Bracket End Plate assembly to the Awning. Tighten the #2 Phillips screws, then the 6mm Roller Bracket Bolt. 35. Reinstall the End Plate on the Front Bar with the three Phillips screws (see Figure 9), and roll the Weather Breaker Front Panel completely up.
  • Page 5 APPENDIX A Resetting Remote Communication and Reprogramming the Motor This procedure will completely reset the communication between the Remote Transmitter and Motor, as well as erase and reprogram the Open and Closed stop position settings of the Motor. This procedure programs the Awning Motor to accept commands from one primary Remote Transmitter. This procedure overwrites the factory set Open and Closed positions with new Open and Closed positions.
  • Page 6 Motor responds with a movement. Note: The Awning Motor will not accept a 3. Your Wall Switch is set to operate your SunSetter Awning. command from the Remote Transmitter for up Test the Awning now for proper operation.

Table of Contents