Table of Contents
Advertisement
Quick Links
GETTING STARTED GUIDE
NI 5783
Four Channel Transceiver Adapter Module
Note
Before you begin, complete the software and hardware installation
instructions in the getting started guide for your FlexRIO FPGA module or
Controller for FlexRIO.
The NI 5783 is a FlexRIO adapter module designed to work in conjunction with FlexRIO
FPGA modules and Controllers for FlexRIO.
The NI 5783 is available in two variants. The NI 5783-01 variant is a 40 MHz Elliptic Filter
(Frequency Domain). The NI 5783-02 variant is a 40 MHz Butterworth Filter (Time Domain).
Unless otherwise specified, all descriptions in this document refer to both variants.
The NI 5783 features 4 analog input channels with 16-bit resolution and sample rates up to
100 MS/s, and 4 analog output channels with 16-bit resolution and sample rates up to
100 MS/s or 200 MS/s.
Note
The NI 5783 is compatible only with NI PXIe-797xR and NI-793xR devices.
This document explains how to install and configure the NI 5783.
Contents
Electromagnetic Compatibility Guidelines............................................................................... 2
FlexRIO Documentation........................................................................................................... 2
Verifying the System Requirements..........................................................................................4
Unpacking................................................................................................................................. 4
Preparing the Environment....................................................................................................... 4
Installing the NI 5783............................................................................................................... 5
Recommended Cables...............................................................................................................6
Accessories................................................................................................................................6
Front Panel and Connector Pinouts...........................................................................................6
AUX I/O Connector.......................................................................................................... 8
Block Diagram.......................................................................................................................... 9
Logic Diagram.......................................................................................................................... 9
Component-Level Intellectual Property (CLIP)..................................................................... 10
NI 5783 CLIP..................................................................................................................10
NI 5783 400 MSPS AO CLIP......................................................................................... 11
Clocking.................................................................................................................................. 11
Advertisement
Table of Contents
Related Manuals for National Instruments 5783
Summary of Contents for National Instruments 5783
-
Page 1: Table Of Contents
The NI 5783 is a FlexRIO adapter module designed to work in conjunction with FlexRIO FPGA modules and Controllers for FlexRIO. The NI 5783 is available in two variants. The NI 5783-01 variant is a 40 MHz Elliptic Filter (Frequency Domain). The NI 5783-02 variant is a 40 MHz Butterworth Filter (Time Domain). -
Page 2: Electromagnetic Compatibility Guidelines
Furthermore, any modifications to the product not expressly approved by National Instruments could void your authority to operate it under your local regulatory rules. - Page 3 Available in NI Example Contains examples of how to run Finder. In LabVIEW, click FPGA VIs and Host VIs on your Help»Find Examples» device. Hardware Input and Output» FlexRIO. NI 5783 Getting Started Guide | © National Instruments | 3...
-
Page 4: Verifying The System Requirements
FlexRIO devices. Verifying the System Requirements To use the NI 5783, your system must meet certain requirements. For more information about minimum system requirements, recommended system, and supported application development environments (ADEs), refer to the readme, which is available on the software media or online at ni.com/updates. -
Page 5: Installing The Ni 5783
Installing the NI 5783 Refer to the getting started guide for your FlexRIO FPGA module or Controller for FlexRIO for instructions about how to install your FlexRIO system, including the NI 5783. Confirming that Measurement & Automation Explorer (MAX) Recognizes the Device Use Measurement &... -
Page 6: Recommended Cables
Recommended Cables NI recommends using the following cables to connect signals to the NI 5783. Cable NI Part Number HDBNC to SMA 769177-01 HDBNC to BNC 769028-01 Accessories The NI 5783 can be used with the SCB-19 shielded desktop connector block. - Page 7 Caution Connections that exceed any of the maximum ratings of any connector on the NI 5783 can damage the device and the chassis. NI is not liable for any damage resulting from such connections. NI 5783 Getting Started Guide | © National Instruments | 7...
-
Page 8: Aux I/O Connector
AUX I/O Connector Table 2. NI 5783 AUX I/O Connector Pin Assignments AUX I/O Connector Pin Signal Signal Description DIO Port 0 (0) Bidirectional single-ended (SE) digital I/O (DIO) data channel. Ground reference for signals. DIO Port 0 (1) Bidirectional SE DIO data channel. -
Page 9: Block Diagram
NI 5783 to the HDMI port of another device. NI is not liable for any damage resulting from such signal connections. Related Information Accessories on page 6 The NI 5783 can be used with the SCB-19 shielded desktop connector block. -
Page 10: Component-Level Intellectual Property (Clip)
4x interpolation, one sample at a time in the Data Clock domain with 8x interpolation, or one sample at a time in the Data Clock 2x domain with 4x interpolation, according to the clock mode selected. 10 | ni.com | NI 5783 Getting Started Guide... -
Page 11: Ni 5783 400 Msps Ao Clip
Related Information Refer to the FlexRIO Help for more information about FlexRIO CLIP items, how to configure the NI 5783 with a socketed CLIP, and for a list of available socketed CLIP signals. NI 5783 400 MSPS AO CLIP This CLIP provides access to four 16-bit 100 MS/s analog input channels, two 16-bit 400 MS/s analog output channels, eight bidirectional DIO channels, four bidirectional PFI channels, and the front panel trigger. - Page 12 60 MHz to 100 MHz external Sample Clock through the CLK/REF IN front panel connector Related Information Refer to the FlexRIO Help for more information about NI 5783 clocks. Worldwide Support and Services The NI website is your complete resource for technical support. At ni.com/support, you have access to everything from troubleshooting and application development self-help resources to email and phone assistance from NI Application Engineers.
- Page 13 LabVIEW FPGA Development Kit Module Help User Manual more about your products through ni.com. Support FlexRIO Services ni.com/support ni.com/flexrio ni.com/services *This item is also installed with the driver software. NI 5783 Getting Started Guide | © National Instruments | 13...
- Page 14 CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S. Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015. © 2016 National Instruments. All rights reserved. 375444A-01 Apr16...