SeaLevel DIO-32.PCI User Manual
Hide thumbs
Also See for DIO-32.PCI:
- User manual (23 pages) ,
- User manual (23 pages) ,
- User manual (24 pages)
Related Manuals for SeaLevel DIO-32.PCI
Summary of Contents for SeaLevel DIO-32.PCI
- Page 1 DIO-32.PCI Users Manual Part # 8004 Sealevel Systems, Inc. Telephone: 864.843.4343 155 Technology Place Fax: 864.843.3067 Liberty, SC 29657 USA www.sealevel.com...
-
Page 2: Table Of Contents
B - H ......................10 PPENDIX SSISTANCE C - S ..........................11 PPENDIX CREEN D - C ........................12 PPENDIX OMPLIANCE OTICES .................12 EDERAL OMMUNICATIONS OMMISSION TATEMENT EMC D .........................12 IRECTIVE TATEMENT ................................13 ARRANTY © Revision December 9, 2003 Sealevel Systems, Incorporated. All rights reserved. -
Page 3: Introduction
Reed relays are well suited for low current applications. The relays are normally open, and close when energized. What’s Included The DIO-32.PCI is shipped with the following items. If any of these items are missing or damaged, contact the supplier. •... -
Page 4: Installation
Do not install the Adapter in the machine until the software has been fully installed. 1. Start Windows. 2. Insert the Sealevel Systems CD in to your CD drive. 3. If ‘Auto-Start’ is enabled for this drive the software will automatically launch. Otherwise, point your browser to the ‘Index.htm’... -
Page 5: Physical Installation
4. Gently insert the PCI adapter into the slot. Make sure that the adapter is seated properly. 5. Replace the screw. (This is required to ensure FCC Part 15 compliance.) 6. Install cable (CA165). 7. Replace the cover. 8. Connect the power cord. Installation is finished. Sealevel Systems DIO-32.PCI Page 3... -
Page 6: Technical Description
Technical Description The DIO-32.PCI provides four parallel input/output (I/O) ports. The ports are organized as ports A, B, C, and D. Port A and B are input ports interfaced to optically-isolated inputs, while ports C and D are reed relay output ports. -
Page 7: Relay Specifications
Contact Resistance, Initial: .15 Ohms • Rated Life: Low Load: 200 Million Closures Maximum Load: 100 Million Closures • Contact Speed: Operate: .5 mS Release: .5 mS Bounce: .5 mS • Maximum Operating Speed: 600 Hertz Sealevel Systems DIO-32.PCI Page 5... -
Page 8: Reading The Inputs
The relay ports return the ones complement of the value that is currently being used to drive the relays. Writing the Outputs: The output ports are the only ports that can be written. The relays on a standard DIO-32.PCI are normally open. To close a relay a one must be written to the appropriate bit. -
Page 9: Register Description
IRQEN = enable interrupts (Base+5) 0 = disabled 1 = enabled (disabled after reset or power up). IRQST = interrupt status (Base+5) 1 = interrupt pending (reading the bit clears interrupt). Bit can not be written. Sealevel Systems DIO-32.PCI Page 7... -
Page 10: Specifications
10 to 90% R.H. Non-Condensing Manufacturing All Sealevel Systems Printed Circuit boards are built to UL 94V0 rating and are 100% electrically tested. These printed circuit boards are solder mask over bare copper or solder mask over tin nickel. Power Consumption... -
Page 11: Appendixa - Troubleshooting
I/O address. 3. Make sure the Sealevel Systems adapter is using a unique IRQ. While the Sealevel Systems adapter does allow the sharing of IRQs, many other adapters (i.e. SCSI adapters & on-board serial ports) do not. The IRQ is typically selected by the BIOS or Operating system. -
Page 12: Appendixb - How T O Geta
3. Sealevel Systems provides an FAQ section on its web site. Please refer to this to answer many common questions. This section can be found at http://www.sealevel.com/faq.asp. -
Page 13: Appendixc - Silk -Screen
Appendix C - Silk-Screen Appendix C - Silk-Screen 4.200" 6.00" 3.825" Sealevel Systems DIO-32.PCI Page 11... -
Page 14: Appendixd - Compliancen
Always use cabling provided with this product if possible. If no cable is provided or if an alternate cable is required, use high quality shielded cabling to maintain compliance with FCC/EMC directives. Sealevel Systems DIO-32.PCI Page 12... -
Page 15: Warranty
(RMA) number. The Customer agrees to insure the Product or assume the risk of loss or damage in transit, to prepay shipping charges to Sealevel, and to use the original shipping container or equivalent. Warranty is valid only for original purchaser and is not transferable.