Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Loctite Hysol 98038
Summary of Contents for Loctite Hysol 98038
- Page 1 ® EQUIPMENT O P E R A T I O N M A N U A L Loctite ® Hysol ® Wheel Coater 98038...
-
Page 2: Table Of Contents
Contents Page No. Please observe the following ........1 Emphasized Sections . -
Page 3: Please Observe The Following
Observe the manufacturer’s instructions as stated in the Material Safety Data Sheet (MSDS). • While under warranty, the machine may be repaired only by an authorized Loctite service representative. • Wear heat resistant leather gloves when operating or maintaining a hot machine. -
Page 4: Items Supplied
Please observe the following (continued) • Allow machine to cool and adhesive to solidify before attempting to move the machine. • A qualified electrician or appliance repair person should perform machine repair. • Do not overfill adhesive pot. Molten adhesive should never be above the ⁄... -
Page 5: Technical Data
Technical Data • Power supply 120V, 15 amp, Single Phase • Power consumption 1100 Watts • Roll surface speed 10 to 40 feet per minute • Dimensions 15" W x 6 ⁄ " H x 22 ⁄ " D • Warm up time Approximately 30 minutes •... -
Page 6: Machine Illustration
Machine Illustration Wheel Coater Model: 98038, 120V, 1100 Watts Loctite Corporation 1001 Trout Brook Crossing Rocky Hill, CT 06067 985278 CAUTION ELECTRICAL HAZARD DISCONNECT FROM POWER SUPPLY BEFORE REMOVING COVER 15" HEATER SWITCH MOTOR SWITCH 22 1/2" Wheel Coater 6 5/16"... -
Page 7: Operation
Operation Set Up • Place the Hysol ® Wheel Coater on a level, heavy-duty bench and preferably one with adjustable legs. • Adjust the height of the table so the working height of the machine is comfortable. • Plug the power cord into a properly grounded 120V, 15-amp outlet. Start Up •... -
Page 8: Film Thickness Adjustment
Operation (continued) Film Thickness Adjustment • Adjusting the clearance between the doctor blade and the roller can change film thickness on the roller. • Loosen the 4 machine screws, which secure the doctor blade. • Place a feeler gauge between the roll and blade at one end of the roll. •... -
Page 9: Care, Cleaning, And Maintenance
Care, Cleaning, and Maintenance Char Removal If the Hysol ® Wheel Coater is over heated a brown or black flaky crust will form on exposed surfaces of the glue pot. This is charred adhesive that can be removed using the following procedure. -
Page 10: Drive Chain
Care, Cleaning, and Maintenance (continued) Drive Chain • Remove chain guard and oil chain monthly if machine is used continuously. • If chain is loose, loosen motor mount screws and slide motor to tighten. Fuse, Motor Controller • The motor controller fuse will blow in the event of a motor overload. •... -
Page 11: Troubleshooting
Troubleshooting Notice: Electrical troubleshooting must be performed by a qualified electrician or appliance repair person. Type of Malfunction Possible Cause Correction No Heat – No power to unit • Plug power cord into proper outlet 120V, 15 amp, Single Phase –... -
Page 12: Assembly Drawing
Documentation (continued) Hysol ® Wheel Coater Assembly Drawing BOTH ENDS 2X 36 CAUTION ELECTRICAL HAZARD DISCONNECT FROM POWER SUPPLY BEFORE REMOVING COVER HEATER SWITCH 4X 38 MOTOR SWITCH 4X 32 4X 37 SHIP WITH MACHINE INSULATION COVERS BOTTOM AND SIDES OF ADHESIVE POT Figure 3... -
Page 13: Wiring Diagram And Schematic
Documentation (continued) Wiring Diagram and Schematic CONDUIT CARRIES HEATER WIRES & PASSES UNDER GEARMOTOR SECURES COILED CORD FOR SHIPMENT HEATER CABLES ENCASE CABLES & CRIMPED END OF RING TERMINAL WITH APPROX. 2" SLEEVE WHITE BLACK SILVER GOLD GREEN SILVER GOLD BLACK ENCASE CABLE &... -
Page 14: Parts List
Documentation (continued) Parts List Item Qty. Description Available Part # Item Qty. Description Available Part # POT, ADHESIVE SCREW, RHMS 10-32 X ⁄ " PHILLIPS 30" STEEL CHAIN AZZ036N01 SCREW, RHMS CONNECTING LINK AZZ036N01 6-32 X ⁄ " PHILLIPS SPROCKET 20T SCREW, SET ⁄... -
Page 15: Warranty
Products including, where products, parts or attachments for use in connection with the Products are available from Loctite, the use of products, parts or attachments which are not manufactured by Loctite, no claim shall be allowed. - Page 16 Loctite Brazil Av. Prof. Vernon Krieble, 91 06690-11-Itapevi São Paulo-Brazil www.loctite.com Loctite and Hysol are trademarks of Loctite Corporation, U.S.A. © Copyright 2001. Loctite Corporation. All rights reserved. Data in this manual is subject to change without notice. P/N985277 10/01 Company...