Subscribe to Our Youtube Channel
Related Manuals for Anthony Liftgates SM Series
Summary of Contents for Anthony Liftgates SM Series
- Page 1 MAINTENANCE MANUAL SM-1800 SM-2500 SM-3000 Quality, Reliability, Customer Service Quality, Reliability, Customer Service Made in the USA Made in the USA...
-
Page 2: Table Of Contents
Maintenance Manual, which is designed to provide you with the necessary instructions and safety precautions for the maintenance of the Side Mount Tuckunder™ liftgate. Typical Anthony Liftgates Side Mount Tuckunder Model. Anthony Liftgates, Inc. Side Mount Maintenance www.anthonyliftgates.com... -
Page 3: General Safety
1.5.1 Maintenance (Dealer) Read, Understand, and WARNING Follow the Manual For additional information, refer to the Anthony Liftgates The success or failure of website www.anthonyliftgates.com to find the most this liftgate to properly and efficiently operate depends current version of the reference material. -
Page 4: Safety
CAUTION MAY result in minor or moderate specifically mentioned by Anthony Liftgates, you must injury. satisfy yourself that they are safe for you and for others. Indicates that equipment or property... -
Page 5: Safety Rules
Always use/set the truck’s parking brake parts must be used to restore the liftgate to the and remove the ignition key before original specifications. Anthony Liftgates will not servicing the liftgate. Failure to follow accept responsibility for damages as a result of using this recommendation can result in injury. -
Page 6: Battery / Fuel Tank Safety
Make sure all parts are in good working grinding or welding. Use ventilation or vacuum condition and properly installed. Replace any systems to remove any contaminated air from the damaged parts immediately. work area. Anthony Liftgates, Inc. Side Mount Maintenance www.anthonyliftgates.com 800-482-0003... -
Page 7: Nomenclature
Frame Rail Reinforcement Floor Extension Channels Assembly Frame Rail Mounting Brackets Transport Latch Pin Mounting Lift Frame Plates Informational Packet Adapter Frame Tube Wheel Arm Radius Arm Main Platform Section Flipover Section Side Mount Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com... -
Page 8: Gravity-Down Power Unit Nomenclature
Breather Cap Motor Start Reservoir Solenoid Adjustable Flow Control Relief Valve Valves Electric Motor Power UP Pump High-Pressure Hose (GREEN wire) (WHITE wire) Control Switch (RED wire) 10 Amp In-Line Fuse (BLACK wire) Anthony Liftgates, Inc. Side Mount Maintenance www.anthonyliftgates.com 800-482-0003... -
Page 9: Maintenance
DO NOT use brake fluid in place of our recommended fluids. Electrical Components 9. Make sure all electrical wires, switches, and connections are in good working condition and operate properly. Side Mount Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com... -
Page 10: Adjusting Wheel Arm
1/2 inch. d. Raise and lower the platform to recheck its position. e. Weld the steel shim plates to the blocks on the platform. Anthony Liftgates, Inc. Side Mount Maintenance www.anthonyliftgates.com 800-482-0003... -
Page 11: Checking The Power Cable
4.8 Checking Motor Start Solenoid and Power 4. If the platform does not align with the floor extension, Cut-off Solenoid contact Anthony Liftgates for a solution to correct the problem. 4.6 Power Cable Fuse - 200 Amp... -
Page 12: Checking Valve Cartridge And Solenoid
Replace the valve if necessary. Refer to “4.9 Checking Valve Cartridge and Solenoid” on page 12. 2. Raise the platform approximately 12 inches off of the floor. Anthony Liftgates, Inc. Side Mount Maintenance www.anthonyliftgates.com 800-482-0003... -
Page 13: Gravity Down Models
3000 2400 psi 14. Reconnect the white wire to the motor start termial. Raise and lower the platform several times to remove any trapped air. Side Mount Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com... - Page 14 Replace with A-150438 10A Fuse. ALI-00596 6. Check the “power down” relief valve pressure in the same way as the “power up” by installing a T-fitting and pressure gauge in the power down port. ALI-00597 Anthony Liftgates, Inc. Side Mount Maintenance www.anthonyliftgates.com 800-482-0003...
-
Page 15: Decals
A-131134 Welding on galvanized and stainless steel parts gives off especially hazardous fumes. • Remove galvanizing from area to weld. • Provide good ventilation. • Wear suitable respirator. A-131125 Side Mount Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com... -
Page 16: Decals
Do not put a higher rated decal on a liftgate with a lower capacity; this could result in liftgate damage or possibly personal injury. Anthony Liftgates, Inc. Side Mount Maintenance www.anthonyliftgates.com 800-482-0003... - Page 17 Kendall Glacial Blu hydraulic fluid. Use ONLY the same or equivalent fluid. A-131133 ttached to control cable) — A-131001 (a 9 — A-150601 only on galvanized liftgates) — A-131125 ( Side Mount Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com...
-
Page 18: Welding Stainless Steel To Galvanized
(the wall separating the nasal passages). Always wear proper breathing protection when grinding or welding. Use ventilation or vacuum systems to remove any contaminated air from the work area. Anthony Liftgates, Inc. Side Mount Maintenance www.anthonyliftgates.com 800-482-0003... -
Page 19: Troubleshooting Chart
Adjustment” on page 10. Replacement part — ATU‑071 SHIM, 14GA Bushing wear where lift arms connect to Replace bushings. Refer to separate platform. Parts Manual. Structural damage. Replace worn parts. Refer to separate Parts Manual. Side Mount Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com... - Page 20 Remove flow control valve and hook hydraulic hose directly to the cylinder. If the cylinder operates properly, replace the valve. “4.14 Checking Flow Control Valve” on page 14. Replacement part — A‑130102. Anthony Liftgates, Inc. Side Mount Maintenance www.anthonyliftgates.com 800-482-0003...
- Page 21 Clear platform operating area. Latch pin will not slide freely to release Activate the “UP” switch and raise the liftgate. liftgate to the fully stored position. The latch pin should slide freely. Side Mount Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com...
- Page 22 Refer to section “4.9 Checking Valve Cartridge and Solenoid” on page 12. Replacement part — A‑130216. Hydraulic pump and motor. Replace power unit. Refer to the separate Parts Manual. Anthony Liftgates, Inc. Side Mount Maintenance www.anthonyliftgates.com 800-482-0003...
- Page 23 Cylinder Piston Seals” on page 12 for additional information. Loosen locknut and turn Allen screw Relief valve is set too low or clogged clockwise to increase pressure. with contaminants. Remove and clean if necessary. Side Mount Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com...
- Page 24 THE ORIGINAL NAME IN LIFTGATES - SINCE 1941 1037 West HOWARD ST. 1037 West HOWARD ST. P.O. BOX 615 P.O. BOX 615 PONTIAC, IL 61764-0615 PONTIAC, IL 61764-0615 PH: 815-842-3383 PH: 815-842-3383 FAX: 815-844-3612 FAX: 815-844-3612 TOLL FREE: 800-482-0003 TOLL FREE: 800-482-0003 WWW.ANTHONYLIFTGATES.COM WWW.ANTHONYLIFTGATES.COM Form No.
Need help?
Do you have a question about the SM Series and is the answer not in the manual?
Questions and answers