Related Manuals for Anthony Liftgates MTU-GLR Series
Summary of Contents for Anthony Liftgates MTU-GLR Series
- Page 1 MAINTENANCE MANUAL MTU-GLR MTU-GLR-WR-3 MTU-GLR-WR-4 MTU-GLR-EX-3 MTU-GLR-EX-4 MTU-GLR-25 MTU-GLR-3 MTU-GLR-4 MTU-GLR-5 MTU-GLR-6 MTU-GLR-3-4 Shown Quality, Reliability, Customer Service Made in the USA...
-
Page 3: Table Of Contents
4.15 Power Module Fluid ... . 15 4.16 Reattach Control Unit Wires to Appropriate Terminals ... 16 MTU-GLR Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com... -
Page 4: General Information
State and Federal standards instructions and safety precautions for the installation of in your area. Anthony Liftgates offers a bolt-on the MTU-GLR TuckUnder™ liftgates. bumper, which meets the requirements of this standard. -
Page 5: Registration
SERVICE and then select WARRANTY CLAIM. operation or other unforeseen problems or dangers. If any deviation is deemed necessary, written permission must be obtained from Anthony Liftgates. 2. All decals must be attached and legible, or all warranties are void. -
Page 6: Safety Icons Nomenclature
This list may include, but is not lowering of the liftgate can cause serious crushing limited to: injuries. • A hard hat. • Protective shoes with slip resistant soles. • Protective goggles, glasses, or face shield. • Protective clothing. Anthony Liftgates, Inc. MTU-GLR Maintenance www.anthonyliftgates.com 800-482-0003... -
Page 7: Equipment / Tools / Parts
Anthony Liftgates will not platform. Always stand away from the edge. When on accept responsibility for damages as a result of using the ground, always stand clear of the liftgate when it unapproved parts. -
Page 8: Welding Or Grinding Galvanized Or Stainless Steel Material
Pump Box Wheel Arm Mounting Plates (bolt on) Lift frame Adapter Frame Tube Transport Latch Pin Flip-over Platform Section Gusset Rubber Dock Bumper Curbside Dock Bumper Corner Cap Radius Arm Main Platform ALI-00357 Anthony Liftgates, Inc. MTU-GLR Maintenance www.anthonyliftgates.com 800-482-0003... - Page 9 Cylinder Electric power down Motor solenoid (WHITE wire) Control connected to starter control Switch terminal 10 Amp In-Line Fuse (BLACK wire) Connected to battery cable terminal Flow Control Valve Control Box Wiring ALI-00370 MTU-GLR Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com...
-
Page 10: Maintenance
1. If adjustment is needed, remove the two bolts and NOTICE use only the recommended nuts on the wheel arm. Hyken Glacial Blu anti-wear, low- viscosity, hydraulic fluid in the power unit reservoir. Anthony Liftgates, Inc. MTU-GLR Maintenance www.anthonyliftgates.com 800-482-0003... -
Page 11: Platform Adjustment
3. To lower the ramp end, remove material from the contact area (arrows shown in Step 2) between the cam plates and platform. 4. If the platform does not align with the floor extension, contact Anthony Liftgates for a solution to correct the problem. MTU-GLR Maintenance Anthony Liftgates, Inc. -
Page 12: Replace The Power Cable Fuse
4. Slide the new heat shrink tube over one side of the Power cut-off solenoid. wiring. 5. Bolt the new fuse to the cable lugs using the bolts, washers, and lock washer, as shown. Anthony Liftgates, Inc. MTU-GLR Maintenance www.anthonyliftgates.com 800-482-0003... -
Page 13: Checking The Power Cable
5. Remove the solenoid from the valve assembly. 6. Remove the valve cartridge from the pump body. 7. Clean the cartridge and blow it dry with compressed air (not greater than 30 psi). Also, blow out the pump body. MTU-GLR Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com... -
Page 14: Replacing Solenoid Valve
Serious injury or pressure hose from the power up port of the pump. death could result if this action is not followed. 2. Install a T-fitting (customer supplied) into the power up port. Anthony Liftgates, Inc. MTU-GLR Maintenance www.anthonyliftgates.com 800-482-0003... -
Page 15: Checking Control Switch Fuse
Black wire ALI-00597 4.15 Power Module Fluid Power down models - With the platform fully raised, Power Down the oil level should be within 2 inches of the top of the reservoir. 2” ALI-00613a MTU-GLR Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com... -
Page 16: Mtu-Glr Maintenance
A-131106 Warning - Remove Bolts After Installation location of the fuse. (attached only to A-133105 200 *Factory Installed – Installer must make sure all decals are attached, as AMP Power Cable) shown. ALI-00393 Anthony Liftgates, Inc. MTU-GLR Maintenance www.anthonyliftgates.com 800-482-0003... -
Page 17: Decals
Do not put a higher rated latch pin after use. decal on a liftgate with a lower capacity; this could result in liftgate damage or possibly personal injury. ATU-423 MTU-GLR Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com... - Page 18 10 AMP FUSE & HOLDER Protects against dead shorts in this "control circuit". If blown, pull "fuse holder cap", replace fuse, replace "cap". If fuse continues to blow, contact a qualified mechanic, "control circuit" may be damaged. Anthony Liftgates, Inc. MTU-GLR Maintenance www.anthonyliftgates.com 800-482-0003...
-
Page 19: Welding Stainless Steel To Galvanized
(the wall separating the nasal passages). Always wear proper breathing protection when grinding or welding. Use ventilation or vacuum systems to remove any contaminated air from the work area. MTU-GLR Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com... -
Page 20: Safety
Remove the oil reservoir and make sure the return tube is below the oil level. If the tube has turned or fallen out, reinstall it into the pump housing. Use a center punch to “stake” the tube into position. Anthony Liftgates, Inc. MTU-GLR Maintenance www.anthonyliftgates.com 800-482-0003... -
Page 21: General Guidelines
Platform operating area is not clear. Clear platform operating area. Latch pin will not slide freely to release Activate the “UP” switch and raise the liftgate. liftgate to the fully stored position. The latch pin should slide freely. MTU-GLR Maintenance Anthony Liftgates, Inc. 800-482-0003 www.anthonyliftgates.com... -
Page 22: Troubleshooting Chart
Replace damaged parts. Low Voltage. Recharge battery (if less than 9 Volts). Lowering valve. See Maintenance section. “4.8 Checking Lowering Valve Cartridge and Solenoid” on page 13. Hydraulic pump and motor. Replace power unit. Anthony Liftgates, Inc. MTU-GLR Maintenance www.anthonyliftgates.com 800-482-0003... - Page 23 NOTES...
- Page 24 MTU-GLR Gentle Level Ride (GLR) Our platform maintains a smooth, level up and down operation until the platform reaches the ground and then tilts gently forward. The platform then re-levels itself at the start of the lifting cycle. THE ORIGINAL NAME IN LIFTGATES - SINCE 1941 1037 West HOWARD ST.
Need help?
Do you have a question about the MTU-GLR Series and is the answer not in the manual?
Questions and answers