Operation - Ryobi DUALCLEAN RPW105DM Operator's Manual

EN
FR DE ES IT PT
please observe the local regulations of local boards
or local water supplier.
To ensure that there is no feedback of contaminant
into the water supply, the appliance must not be
connected directly to the public drinking water
supply mains.
If the appliance is connected to potable water
mains, backflow prevention devices should be
incorporated in or fixed to the water supply system.
The installation should be accepted by local boards
or water supplier and should be conducted by
professional technical personnel. The backflow
prevention devices should be appropriate to fluid
categories and comply with the requirement to
avoid back siphonage according to EN 60335-2-79/
A2: 2007.
Before connecting the garden hose to the pressure
washer:
Run water through the hose for 30 seconds to clean
■
any debris from the hose.
Inspect the filter in the water intake.
■
If the filter is damaged, do not use the machine until
■
the filter has been replaced.
If the filter is dirty, clean it before connecting the
■
garden hose to the machine.
Attach the self-coiling hose to the water intake
■
coupler.
Screw the threaded tap connector into the self-coiling
hose.
Straighten the garden hose.
■
NOTE: There must be a minimum of 3 metres of
unrestricted hose between the pressure washer intake
and the garden tap.
With the garden tap turned completely off, attach the
■
end of the garden hose to the threaded tap connector.
USING THE LANCE AS A HANDLE
See Figure 6.
When not in use, the lance can be stored in the cleaning
deck. In this position, the lance is then used as a handle
to push/move the pressure washer from place to place.
Attaching the lance to the cleaning deck:
Assemble the gun and lance as described previously
■
in this manual.
Insert the lance Quick Connect coupler into the clean-
■
ing deck inlet plug. Tilt upwards until coupler clips into
position.
WARNING:
To reduce the risk of injection or injury, only use
the cleaning deck on fl at, horizontal surfaces.
RPW105DM 25lgs.indd 17 RPW105DM 25lgs.indd 17
NL SV DA NO FI HU CS RU
English(Original instructions)

OPERATION

Applications
This pressure washer can be used for the purposes listed
below:
■
■
ADDING DETERGENT TO THE PRESSURE WASHER
See Figure 8.
Use only detergents designed for pressure washers;
household detergents, acids, alkalines, bleaches,
solvents, flammable material, or industrial grade solutions
can damage the pump. Many detergents may require
mixing prior to use.
Prepare cleaning solution as instructed on the solution
bottle.
■
■
■
■
■
STARTING AND STOPPING THE PRESSURE
WASHER
See Figure 9.
■
■
■
■
■
17
RO PL SL HR ET
Never lift the cleaning deck from the cleaning
surface while operating the pressure washer.
Removing dirt and mould from decks, cement patios,
and walls
Cleaning cars, boats, motorcycles, outdoor furniture
and barbeques
Disconnect pressure washer from power supply.
Place pressure washer upright on a flat surface.
Remove cap from detergent tank.
Pour detergent into tank until it reaches the maximum
fill level located on the unit.
NOTE: Use a funnel, if needed, to prevent accidental
spilling of the detergent outside the tank. If any
detergent is spilled during the filling process, make
sure the unit is cleaned and dried before proceeding.
Reinstall cap.
CAUTION:
Do not run the pump without the water supply
connected and turned on.
Connect the garden hose.
Turn the garden hose on then squeeze the high
pressure trigger to relieve air pressure. Once a steady
stream of water appears, release the trigger.
After ensuring the switch is in the OFF position,
connect the pressure washer to the power supply.
Press ON ( I ) on the switch to start the motor.
To stop the motor, release the trigger and press OFF
( O ) on the switch.
LT LV SK BG
2009/12/11 2009/12/11 3:50 3:50