Subscribe to Our Youtube Channel
Related Manuals for S&T Kontron KBox E-410-APL
Summary of Contents for S&T Kontron KBox E-410-APL
- Page 1 USER GUIDE KBox E-410-APL Doc. User Guide, Rev. 1.0 Doc. ID: [To be Determined] www.kontron.com // 1...
- Page 2 KBox E-410-APL - User Guide, Rev. 1.0 This page has been intentionally left blank www.kontron.com // 2...
- Page 3 KBox E-410-APL - User Guide, Rev. 1.0 KBOX E-410-APL - USER GUIDE Disclaimer Kontron would like to point out that the information contained in this user guide may be subject to alteration, particularly as a result of the constant upgrading of Kontron products. This document does not entail any guarantee on the part of Kontron with respect to technical processes described in the user guide or any product characteristics set out in the user guide.
- Page 4 KBox E-410-APL - User Guide, Rev. 1.0 High Risk Applications Hazard Notice THIS DEVICE AND ASSOCIATED SOFTWARE ARE NOT DESIGNED, MANUFACTURED OR INTENDED FOR USE OR RESALE FOR THE OPERATION OF NUCLEAR FACILITIES, THE NAVIGATION, CONTROL OR COMMUNICATION SYSTEMS FOR AIRCRAFT OR OTHER TRANSPORTATION, AIR TRAFFIC CONTROL, LIFE SUPPORT OR LIFE SUSTAINING APPLICATIONS, WEAPONS SYSTEMS, OR ANY OTHER APPLICATION IN A HAZARDOUS ENVIRONMENT, OR REQUIRING FAIL-SAFE PERFORMANCE, OR IN WHICH THE FAILURE OF PRODUCTS COULD LEAD DIRECTLY TO DEATH, PERSONAL INJURY, OR SEVERE PHYSICAL OR...
- Page 5 KBox E-410-APL - User Guide, Rev. 1.0 Revision History Revision Brief Description of Changes Date of Issue Initial Issue 2020-May-27 Terms and Conditions Kontron warrants products in accordance with defined regional warranty periods. For more information about warranty compliance and conformity, and the warranty period in your region, visit http://www.kontron.com/terms- and-conditions.
-
Page 6: Symbols
KBox E-410-APL - User Guide, Rev. 1.0 Symbols The following symbols may be used in this user guide DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. -
Page 7: For Your Safety
KBox E-410-APL – User Guide, Rev. 1.0 For Your Safety Your new Kontron product was developed and tested carefully to provide all features necessary to ensure its compliance with electrical safety requirements. It was also designed for a long fault-free life. However, the life expectancy of your product can be drastically reduced by improper treatment during unpacking and installation. -
Page 8: Lithium Battery Precautions
KBox E-410-APL - User Guide, Rev. 1.0 Lithium Battery Precautions If your product is equipped with a lithium battery, take the following precautions when replacing the battery. Danger of explosion if the battery is replaced incorrectly. Replace only with same or equivalent battery type recommended by the manufacturer. ... -
Page 9: Table Of Contents
KBox E-410-APL - User Guide, Rev. 1.0 Table of Contents Symbols ..........................................6 For Your Safety ........................................7 High Voltage Safety Instructions .................................. 7 Special Handling and Unpacking Instruction ............................7 Lithium Battery Precautions ..................................8 General Instructions on Usage ..................................8 Quality and Environmental Management .............................. - Page 10 KBox E-410-APL - User Guide, Rev. 1.0 Accessing Internal Components ..............................26 5.1. Opening and Closing the KBox E-410-APL ............................27 5.1.1. Installing SO-DIMM memory modules ............................28 5.1.2. Installing an HDD / SSD ..................................28 5.1.3. Installing an mPCIe expansion card ..............................29 5.1.4.
-
Page 11: List Of Tables
KBox E-410-APL - User Guide, Rev. 1.0 List of Tables Table 1: DB9 Port Configuration .................................. 23 Table 2: Technical Specifications ................................44 Table 3: Mechanical Specifications ................................45 Table 4: Environmental Conditions ................................46 Table 5: Standards and Certifications ..............................46 Table 6: DC Power Input (see Figure 1, pos.1) ............................ - Page 12 KBox E-410-APL - User Guide, Rev. 1.0 Figure 35: BIOS Boot Setup Menu ................................70 Figure 36: BIOS Security Setup Menu ................................. 71 Figure 37: BIOS Security Setup Menu - Secure Boot ..........................72 Figure 38: BIOS Security Setup Menu - Secure Boot - Key Management* ................... 73 Figure 39: BIOS Boot Setup Menu ................................
-
Page 13: 1/ General Safety Instructions For It Equipment
KBox E-410-APL - User Guide, Rev. 1.0 1/ General Safety Instructions for IT Equipment Please read this chapter carefully and take careful note of the instructions, which have been compiled for your safety and to ensure to apply in accordance with intended regulations. If the following general safety instructions are not observed, it could lead to injuries to the operator and/or damage of the product;... - Page 14 KBox E-410-APL - User Guide, Rev. 1.0 Additional safety instructions for DC power supply circuits To guarantee safe operation of devices with DC power supply voltages larger than 60 volts DC or a power consumption larger than 240 VA, please observe that: ...
-
Page 15: Electrostatic Discharge (Esd)
KBox E-410-APL - User Guide, Rev. 1.0 1.1. Electrostatic Discharge (ESD) A sudden discharge of electrostatic electricity can destroy static-sensitive devices or micro-circuitry. Therefore proper packaging and grounding techniques are necessary precautions to prevent damage. Always take the following precautions: Transport boards in ESD-safe containers such as boxes or bags. - Page 16 KBox E-410-APL - User Guide, Rev. 1.0 A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas Do not dispose of lithium batteries in general trash collection. Dispose of the battery according to the local regulations dealing with the disposal of these special materials, (e.g.
-
Page 17: 2/ Electromagnetic Compatibility
KBox E-410-APL - User Guide, Rev. 1.0 2/ Electromagnetic Compatibility For detailed information refer to section 10.3 “CE Directives and Standards”. 2.1. Electromagnetic Compatibility (EU) This product has been designed for low level of radiated emission for residential, commercial and light industrial environments and high immunity level for industrial environmental. -
Page 18: 3/ Shipment And Unpacking
KBox E-410-APL - User Guide, Rev. 1.0 3/ Shipment and Unpacking Please check that your package is complete, and contains the items below (according to the ordered unit configuration). If you discover damaged or missing items, please contact your dealer. 3.1. -
Page 19: 4/ System Overview
KBox E-410-APL - User Guide, Rev. 1.0 4/ System Overview The KBox E-410-APL is a fanless system enclosed within a robust compact aluminum chassis with cooling fins, offering the superior qualities for operation in harsh environments. It can be optionally factory-equipped with an mPCIe WLAN, Bluetooth or combo card for two antennas. Users may choose the implementation of a 2.5"... -
Page 20: System Expansion Capabilities
KBox E-410-APL - User Guide, Rev. 1.0 4.1. System Expansion Capabilities 4.1.1. System Expansion via SATA Interface The KBox E-410-APL comes with a 15+7-pin SATA power / data cable connector with the other end pre-connected to the onboard SATA data connector and drive power output wafer. Users can expand the system with a 2.5" SATA HDD / SSD drive. -
Page 21: Front I/O Panel
KBox E-410-APL - User Guide, Rev. 1.0 4.2. Front I/O Panel Figure 1: Front I/O Panel DC-In (see Chapter 4.2.1) Power Switch (See Chapter 4.2.2) Power LED (see Chapter 4.2.3) Storage LED (see Chapter 4.2.4) DP (see Chapter 4.2.5) HDMI (see Chapter 4.2.6) GbE (see Chapter 4.2.7) USB 3.0 (see Chapter 4.2.8) DB9 Port (see Chapter 4.2.9) -
Page 22: Power Switch
KBox E-410-APL - User Guide, Rev. 1.0 4.2.2. Power Switch Press this switch to turn the system on or off. Even when the system is turned off via the power switch there is still a standby voltage on the baseboard. The unit is only completely disconnected from the DC mains, when the power is removed. -
Page 23: Db9 Port
KBox E-410-APL - User Guide, Rev. 1.0 4.2.9. DB9 Port The KBox E-410-APL reserves four cutouts to flexibly accommodate 9-pin D-SUB connectors. Kontron has defined the port configuration as listed in the following table. Table 1: DB9 Port Configuration Port X1 Port X2 Port X3 Port X4... -
Page 24: Internal View
KBox E-410-APL - User Guide, Rev. 1.0 4.3. Internal View Figure 3: Internal view - Baseboard DDR3L SO-DIMM Memory Socket (DIMM1 & DIMM2, see Chapter 4.3.1) 15+7-pin SATA Power / Data Connector (see Chapter 4.3.2) mPCIe Socket (MPCIE1, see Chapter 4.3.3) M.2 Key B Socket (CON1, see Chapter 4.3.4) mPCIe Fixing Bolt M.2 Fixing Bolt for Key B Type 22x42... -
Page 25: Mpcie Socket
KBox E-410-APL - User Guide, Rev. 1.0 4.3.3. mPCIe Socket The KBox E-410-APL reserves one mPCIe socket, allowing the expansion with a full-sized mPCIe WLAN, Bluetooth or combo card. This socket may be unavailable in case you order a model with CAN Bus ports on the I/O panel. 4.3.4. -
Page 26: 5/ Accessing Internal Components
KBox E-410-APL - User Guide, Rev. 1.0 5/ Accessing Internal Components This section contains important information that you must read before accessing the internal components. You must follow these procedures properly when installing, removing or handling any board. It is recommended to expand your system with an additional mPCIe and / or M.2 card(s) before it is installed into an equipment, machine or cabinet. -
Page 27: Opening And Closing The Kbox E-410-Apl
KBox E-410-APL - User Guide, Rev. 1.0 5.1. Opening and Closing the KBox E-410-APL Before opening the KBox E-410-APL, the system must be switched off and disconnected from the main power supply. Also, disconnect all peripheral devices from the KBox E- 410-APL. -
Page 28: Installing So-Dimm Memory Modules
KBox E-410-APL - User Guide, Rev. 1.0 Lift the access cover up. Now you have access to the internal DDR3L SO-DIMM, 2.5" SATA HDD / SSD, mPCIe and M.2 connectors / slots / sockets respectively in order to remove or install hardware components. For closing replace carefully the access cover to the system and screw it on with the retained screws. -
Page 29: Installing An Mpcie Expansion Card
KBox E-410-APL - User Guide, Rev. 1.0 2.5" HDD / SSD Bracket 2.5" HDD / SSD Bracket Screw Hole Connect the SATA power / data connector (Figure 3, pos. 2) to the HDD / SSD. In order to close the KBox E-410-APL, proceed step 6 & 7 described in the subsection 5.1 "Opening and Closing the KBox E-410-APL". - Page 30 KBox E-410-APL - User Guide, Rev. 1.0 Press the M.2 expansion card down on the side with the fixing hole and secure it with the available fastening screw (Figure 3, pos. 6). In order to close the KBox E-410-APL, proceed step 6 - 7 described in the subsection 5.1 "Opening and Closing the KBox E-410-APL".
-
Page 31: 6/ Thermal Considerations
KBox E-410-APL - User Guide, Rev. 1.0 6/ Thermal Considerations 6.1. Available Processors Please refer to the chapter 10/ "Technical Specifications". The list of processors may be extended over the product lifetime. 6.2. Convection Cooling The applied cooling method provides adequate cooling of the device during operation and performs a one-way thermal transfer to the chassis. -
Page 32: 7/ Installation Instructions
Only personnel with appropriate qualifications, trainings and authorization are permitted to install and work with the Kontron KBox E-410-APL. This device shall only be installed in or connected to systems that fulfill all necessary technical and specific environmental requirements. -
Page 33: System Mounting
KBox E-410-APL - User Guide, Rev. 1.0 7.1. System Mounting In order to adapt the KBox E-410-APL for mounting Kontron offers different mounting solution such as: KBox E-410-APL configuration with a DIN rail mounting kit for vertical or horizontal installation into a control cabinet / custom enclosure / machine ... -
Page 34: Figure 9: Securing The Din Rail Clamp (Horizontal Installation)
KBox E-410-APL - User Guide, Rev. 1.0 Figure 9: Securing the DIN rail clamp (Horizontal Installation) Make sure that DIN rail mounting clamp is in the upright position. Clip the top of the DIN rail clamp into the DIN rail and push the bottom of the DIN rail firmly until it clamps onto the bottom of the DIN rail. -
Page 35: Vesa Mounting
KBox E-410-APL - User Guide, Rev. 1.0 Figure 11: Clamping the KBox E-410-APL onto the DIN rail (Horizontal Installation) 7.1.2. VESA Mounting Depending on the ordered KBox E-410-APL configuration, your system may be supplied with a VESA mounting kit (Figure 12). The kit consists of two parts: a base bracket (Figure 12, pos. 1) to be fixed permanently on the mounting surface and another hooked bracket to hold the KBox E-410-APL with a hand-screw knob (Figure 12, pos. -
Page 36: Figure 14: Securing The Base Mounting Bracket
KBox E-410-APL - User Guide, Rev. 1.0 To mount the KBox E-410-APL please proceed according to the steps described: Prepare the mounting surface with sufficient screws (four screws for VESA mount) and if necessary anchors corresponding to the mounting surface type if no VESA-compliant screw holes are available. (The recommended screw size is M4 x 6 ~ 10 mm but it still depends on the available screw holes of the mounting surface and never be larger than M4 if any.) Secure the base mounting bracket to the mounting surface with screws (Figure 14). -
Page 37: Figure 16: Securing The Kbox E-410-Apl Onto The Mounting Surface
KBox E-410-APL - User Guide, Rev. 1.0 Place the KBox E-410-APL onto the mounting surface by sliding the hooked mounting bracket into the based mounting bracket (Figure 16). Secure the hand-screw knob located on the hooked mounting bracket to fix two brackets (Figure 16). Figure 16: Securing the KBox E-410-APL onto the mounting surface For a sufficient air circulation around the device, we recommend keep a proper clearance and not mount / operate any other devices within the clearance around the... -
Page 38: Dc Power Connection
KBox E-410-APL - User Guide, Rev. 1.0 7.2. DC Power Connection The KBox E-410-APL is connected by a 3-pin Phoenix connector (Figure 1, pos. 1) via a DC power supply wiring to a DC power source. In case you order a power adapter from Kontron, the KBox E-410-APL is delivered with a power adapter with a 3-pin Phoenix power plug terminal attached as well as a power cord, For DC power connection, users can use the power cord and power adapter to carry AC power from AC power source and then convert it into DC 24 V. - Page 39 KBox E-410-APL - User Guide, Rev. 1.0 www.kontron.com // 39...
-
Page 40: 8/ Starting Up
KBox E-410-APL - User Guide, Rev. 1.0 8/ Starting Up The KBox E-410-APL must be only operated with the nominal voltage of 15 V ~ 35 V DC of type SELV. For details refer to the chapter 10/ “Technical Specifications”. 8.1. - Page 41 KBox E-410-APL - User Guide, Rev. 1.0 For connection to DC main power supply Ensure that the DC power source is switched off via a disconnecting device (circuit breaker), in order to ensure that no power is flowing from the external DC power source during the connection procedure. Connect the Phoenix power plug terminal prepared as described in the subsection 7.2.1 "Cabling"...
-
Page 42: Operating System And Hardware Component Drivers
KBox E-410-APL - User Guide, Rev. 1.0 8.2. Operating System and Hardware Component Drivers Your system can be supplied optionally with a pre-installed operating system. If you have ordered your KBox E-410-APL with a pre-installed operating system, all drivers are installed in accordance with the system configuration ordered (optional hardware components). -
Page 43: 9/ Maintenance And Cleaning
KBox E-410-APL - User Guide, Rev. 1.0 9/ Maintenance and Cleaning Equipment from Kontron requires only minimum servicing and maintenance for proper operation. For light soiling, clean the KBox E-410-APL with a dry cloth. Carefully remove dust from the surface of the cooling fins of the chassis using a clean, soft brush. -
Page 44: Technical Specifications
KBox E-410-APL - User Guide, Rev. 1.0 Technical Specifications Table 2: Technical Specifications System Processor Intel® Atom® E3900 Series and Pentium® / Celeron® N-Series Processors Memory 2x DDR3L SO-DIMM memory socket Video Display Interface 1x DP (on front) ... -
Page 45: Mechanical Specifications
KBox E-410-APL - User Guide, Rev. 1.0 10.1. Mechanical Specifications Table 3: Mechanical Specifications Construction Aluminum Chassis Dimensions (W x D x H) 205 mm x 125 mm x 65.5 mm / 8.07" x 4.92" x 2.58" Weight 1700 g / 3.75 lb Mounting DIN Rail Mount VESA Mount (75 mm x 75 mm) -
Page 46: Environmental Conditions
KBox E-410-APL - User Guide, Rev. 1.0 10.2. Environmental Conditions Table 4: Environmental Conditions Operating Temperature 0 °C ~ 50 °C / 32 °F ~ 122 °F Storage Temperature -20 °C ~ 80 °C / -4 °F ~ 176 °F Humidity 0 % ~ 95 % 10.3. -
Page 47: 11/ Standard Interfaces - Pin Assignments
KBox E-410-APL - User Guide, Rev. 1.0 11/ Standard Interfaces – Pin Assignments Low-active signals are indicated by a minus sign. 11.1.1. DC Power Input Table 6: DC Power Input (see Figure 1, pos.1) Signal Name DC Power Input (3-pin Phoenix Connector) +15VDC ~ 35VDC (input) 0V (input) Ground... -
Page 48: Dp Connector
KBox E-410-APL - User Guide, Rev. 1.0 11.1.4. DP Connector Table 9: DP Connector (see Figure 1, pos. 8) Signal Name DP Connector TX0+ TX0- TX1+ TX1- TX2+ TX2- TX3+ TX3- AUX+ AUX- www.kontron.com // 48... -
Page 49: Hdmi Connector
KBox E-410-APL - User Guide, Rev. 1.0 11.1.5. HDMI Connector Table 10: HDMI Connector (see Figure 1, pos. 6) Signal Name HDMI Connector Type A Version 1.4 TMDS Data2+ Ground TMDS Data2– TMDS Data1+ Ground TMDS Data1– TMDS Data0+ Ground TMDS Data0–... -
Page 50: Db9 Port
KBox E-410-APL - User Guide, Rev. 1.0 11.1.6. DB9 Port DB9 ports have four possibilities of pin assignments depending on ordered configuration (see Subsection 4.2.9). RS232/422/485 (Port X1 & X2) RS232 (Port X3 & Port X4) CAN Bus (Port X3 & X4) ... -
Page 51: Table 13: Can Bus (See Figure 1, Pos. 9)
KBox E-410-APL - User Guide, Rev. 1.0 Table 13: CAN Bus (see Figure 1, pos. 9) Signal Name CAN Bus (9-pin D-SUB Male Connector) CAN-L CAN-H Table 14: DIO Port (see Figure 1, pos. 9) Signal Name DIO Port (9-pin D-SUB Female Connector) DIO_0 DIO_1 DIO_2... -
Page 52: 12/ Uefi Bios
KBox E-410-APL - User Guide, Rev. 1.0 uEFI BIOS 12.1. Starting the uEFI BIOS The KBox E-410-APL is provided with a Kontron-customized, pre-installed and configured version of AMI Aptio® V uEFI BIOS. AMI BIOS firmware is based on the Unified Extensible Firmware Interface (uEFI) specification and the Intel® Platform Innovation Framework for EFI. -
Page 53: Setup Menus
KBox E-410-APL - User Guide, Rev. 1.0 12.2. Setup Menus The Setup utility features shows six menus in the selection bar at the top of the screen: Main Advanced Power Boot Security Save & Exit The Setup menus are selected via the left and right arrow keys. -
Page 54: Figure 19: Bios Main Menu Screen System Data And Time
KBox E-410-APL - User Guide, Rev. 1.0 Figure 19: BIOS Main Menu Screen System Data and Time BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Product Information Product Name KBox E-410-APL-E3940 BIOS Version R1.01 (x64) BIOS Build Date 12/25/2019 ME FW Version 3.1.70.2334... -
Page 55: Advanced Setup Menu
KBox E-410-APL - User Guide, Rev. 1.0 12.2.2. Advanced Setup Menu The Advanced setup menu provides sub-screens and functions for advanced configurations. The following sub- screen functions are included in the menu: LAN & Audio Configuration Display Configuration ... -
Page 56: Figure 21: Bios Advanced Menu - Display Configuration
KBox E-410-APL - User Guide, Rev. 1.0 Figure 21: BIOS Advanced Menu - Display Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Display Information Primary Display [IGD] → ←: Select Screen UWA Frame Buffer Size [256MB] ↑... -
Page 57: Figure 22: Bios Advanced Menu - Super Io Configuration
KBox E-410-APL - User Guide, Rev. 1.0 Figure 22: BIOS Advanced Menu - Super IO Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Super IO Configuration > Serial Port 1 Configuration → ←: Select Screen > Serial Port 2 Configuration ↑... -
Page 58: Figure 23: Bios Advanced Menu - Super Io Configuration - Serial Port 1 Configuration
KBox E-410-APL - User Guide, Rev. 1.0 Figure 23: BIOS Advanced Menu - Super IO Configuration - Serial Port 1 Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Serial Port 1 Configuration Serial Port [Enabled] → ←: Select Screen Device Settings IO=3F8h;... -
Page 59: Figure 24: Bios Advanced Menu - Super Io Configuration - Serial Port 2 Configuration
KBox E-410-APL - User Guide, Rev. 1.0 Figure 24: BIOS Advanced Menu - Super IO Configuration - Serial Port 2 Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Serial Port 2 Configuration Serial Port [Enabled] → ←: Select Screen Device Settings IO=2F8h;... -
Page 60: Figure 25: Bios Advanced Menu - Super Io Configuration - Serial Port 3 Configuration
KBox E-410-APL - User Guide, Rev. 1.0 Figure 25: BIOS Advanced Menu - Super IO Configuration - Serial Port 3 Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Serial Port 3 Configuration Serial Port [Enabled] → ←: Select Screen Device Settings IO=3E8h;... -
Page 61: Figure 26: Bios Advanced Menu - Super Io Configuration - Serial Port 4 Configuration
KBox E-410-APL - User Guide, Rev. 1.0 Figure 26: BIOS Advanced Menu - Super IO Configuration - Serial Port 4 Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Serial Port 4 Configuration Serial Port [Enabled] → ←: Select Screen Device Settings IO=2E8h;... -
Page 62: Figure 27: Bios Advanced Menu - Cpu Chipset Configuration
KBox E-410-APL - User Guide, Rev. 1.0 Figure 27: BIOS Advanced Menu - CPU Chipset Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit CPU Chipset Configuration EIST [Enabled] → ←: Select Screen Turbo Mode [Enabled] ↑ ↓: Select Item Active Processor Cores [Disabled] Enter: Select... -
Page 63: Figure 28: Bios Advanced Menu - Sata Configuration
KBox E-410-APL - User Guide, Rev. 1.0 Figure 28: BIOS Advanced Menu - SATA Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit SATA Configuration SATA Controller(s) [Enabled] → ←: Select Screen SATA Mode Selection [AHCI] ↑ ↓: Select Item Enter: Select Serial ATA Port 1 [Not Installed]... -
Page 64: Figure 29: Bios Advanced Menu - Usb Configuration
KBox E-410-APL - User Guide, Rev. 1.0 Figure 29: BIOS Advanced Menu - USB Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit USB Configuration USB Devices: → ←: Select Screen 1 Keyboard, 1 Mouse ↑ ↓: Select Item Enter: Select Legacy USB Support [Enabled]... -
Page 65: Figure 30: Bios Advanced Menu - Dio Configuration
KBox E-410-APL - User Guide, Rev. 1.0 Figure 30: BIOS Advanced Menu - DIO Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit DIO Configuration User Configuration [Disabled] DIO_0* [Output High] DIO_1* [Output High] DIO_2* [Output High] DIO_3* [Output High] DIO_4*... -
Page 66: Figure 31: Bios Advanced Menu - Network Stack
KBox E-410-APL - User Guide, Rev. 1.0 Figure 31: BIOS Advanced Menu - Network Stack BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Network Stack [Disabled] Ipv4 PXE Support* [Enabled] Ipv6 PXE Support* [Enabled] → ←: Select Screen ↑... -
Page 67: Figure 32: Bios Advanced Menu - H/W Monitor
KBox E-410-APL - User Guide, Rev. 1.0 Figure 32: BIOS Advanced Menu - H/W Monitor BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit PC Health Status CPU Temperature : +34 C → ←: Select Screen System Temperature : +35 C ↑... -
Page 68: Power Setup Menu
KBox E-410-APL - User Guide, Rev. 1.0 12.2.3. Power Setup Menu The Power setup menu provides functions and a sub-screen for power configurations. The following sub-screen function is included in the menu: WatchDog Timer Configuration Figure 33: BIOS Power Setup Menu BIOS SETUP UTILITY Main Advanced... -
Page 69: Figure 34: Bios Power Setup Menu - Watchdog Timer Configuration
KBox E-410-APL - User Guide, Rev. 1.0 Figure 34: BIOS Power Setup Menu - WatchDog Timer Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit WatchDog Timer Configuration WDT Function [Disabled] → ←: Select Screen WDT Count Mode* [Second] ↑... -
Page 70: Boot Setup Menu
KBox E-410-APL - User Guide, Rev. 1.0 12.2.4. Boot Setup Menu The boot setup menu lists the for boot device priority order, that is generated dynamically. Figure 35: BIOS Boot Setup Menu BIOS SETUP UTILITY Main Advanced Power Boot Security Save &... -
Page 71: Security Setup Menu
KBox E-410-APL - User Guide, Rev. 1.0 12.2.5. Security Setup Menu The Security setup menu provides information about the passwords and functions for specifying the security settings, as well as a sub-screen for secure boot. The passwords are case-sensitive. The KBox E-410-APL provides no factory- set passwords. -
Page 72: Figure 37: Bios Security Setup Menu - Secure Boot
KBox E-410-APL - User Guide, Rev. 1.0 Password length requirements are maximum 20 characters and minimum 3 characters. Figure 37: BIOS Security Setup Menu - Secure Boot BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit System Mode Setup Vendor Keys Not Modified... -
Page 73: Figure 38: Bios Security Setup Menu - Secure Boot - Key Management
KBox E-410-APL - User Guide, Rev. 1.0 Figure 38: BIOS Security Setup Menu - Secure Boot - Key Management* BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Factory Key Provision [Disabled] > Restore Factory Keys > Reset to Setup Mode >... - Page 74 KBox E-410-APL - User Guide, Rev. 1.0 Feature Option Description Key], [Delete Var] Forbidden Signatures [Save To File], [Set New Var], [Append Key], [Delete Var] Authorized [Set New Var], TimeStamps [Append Key] OsRecovery [Set New Var], Signatures [Append Key] www.kontron.com // 74...
-
Page 75: Remember The Password
KBox E-410-APL - User Guide, Rev. 1.0 12.2.5.1. Remember the password It is highly recommended to keep a record of all passwords in a safe place. Forgotten passwords results in being locked out of the system. If the system cannot be booted because the User Password or the Supervisor Password are not know, contact Kontron Support for further assistance. -
Page 76: Save & Exit Setup Menu
KBox E-410-APL - User Guide, Rev. 1.0 12.2.6. Save & Exit Setup Menu The exit setup menu provides functions for handling changes made to the UEFI BIOS settings and the exiting of the setup program. Figure 39: BIOS Boot Setup Menu BIOS SETUP UTILITY Main Advanced... -
Page 77: Appendix A: List Of Acronyms
KBox E-410-APL - User Guide, Rev. 1.0 Appendix A: List of Acronyms The following table does not contain the complete acronyms used in signal names, signal type definitions or similar. A description of the signals is included in the I/O Connector and Internal connector chapters within this user guide. -
Page 78: About Kontron
KBox E-410-APL – User Guide, Rev. 1.0 About Kontron Kontron is a global leader in embedded computing technology (ECT). As a part of technology group S&T, Kontron offers a combined portfolio of secure hardware, middleware and services for Internet of Things (IoT) and Industry 4.0 applications.
Need help?
Do you have a question about the Kontron KBox E-410-APL and is the answer not in the manual?
Questions and answers