1. Manuals
  2. Brands
  3. DNF Controls Manuals
  4. Controller
  5. ST600-KIPRO
  6. User manual

DNF Controls ST600-KIPRO User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ST600-KIPRO
User Manual
ST600-KIPRO User Manual
Page 1 of 16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ST600-KIPRO and is the answer not in the manual?

Questions and answers

Related Manuals for DNF Controls ST600-KIPRO

Summary of Contents for DNF Controls ST600-KIPRO

  • Page 1 ST600-KIPRO User Manual ST600-KIPRO User Manual Page 1 of 16...

  • Page 2: Table Of Contents

    CONNECTION TO AJA KI-PRO .................. 7 OPERATION ......................8 CLIP LIST WEB PAGE ................... 10 8. FUNCTION TABLE ....................11 9. KEY LAYOUT ....................... 13 10. SPECIFICATIONS ....................14 11 DNF CONTROLS LIMITED WARRANTY ..............16 REVISIONS 1.00 01/24/17 Original draft. ST600-KIPRO User Manual...

  • Page 3: Getting Started

    3. Go to Remote Device Assignment Section to enter IP addresses for remote devices that ST600 will communicate with. 4. Go to System Configuration section to set default settings. 2. EQUIPMENT LIST Qty Component DNF Part Number ST600 Panel ST600-KIPRO ST600 POWER SUPPLY included POWER CORD included ST600-KIPRO User Manual Page 3 of 16...

  • Page 4: Installation

    It cannot be viewed or modified with a text editor. To access the System Configuration web page, use the following log-on when prompted: Username: dnfuser Password: controls ST600-KIPRO User Manual Page 4 of 16...

  • Page 5: System Configuration Web Page

    SELECTION DESCRIPTION P1 Software Upgrade: Use this link to install the P1 upgrade file provided by DNF Controls P2 Software Upgrade: Use this link to install the P2 upgrade file provided by DNF Controls Web Upgrade: Use this link to install the Web pages upgrade file provided by DNF...
  • Page 6 Enter Label: Enter label to be displayed on top right of all web pages Enter the new IP settings below: Enter the new IP address, Gateway, and Subnet Mask. Click on “Save Config” to save the new entries. The ST600 will automatically reboot. ST600-KIPRO User Manual Page 6 of 16...

  • Page 7: Connection To Aja Ki-Pro

    5. CONNECTION TO KI PRO Using a Web browser, enter the IP address of the ST600-Kipro panel to access the configuration pages. Select the Remote Device Assignment link located on the left hand side of the web page. In the Remote Device Assignment page, create a device label for the AJA KIPRO you will be connecting to.

  • Page 8: Operation

    See Function Table (Pg 12) for a full list of functions and a description of each function. CREATE AND RECORD CLIP FROM WEB PAGE Using a Web browser, enter the IP address of the ST600-Kipro panel to access the configuration pages.
  • Page 9 LOAD A CLIP FROM ST600-KIPRO Press [SHIFT/ESC] + [LOAD] to set the ST600-KiPRO into a “LOAD” mode. Once in “LOAD” mode, use numeric keys 0-9 of the panel (yellow silkscreen) to call up the desired clip number After the numeric clip ID is entered, Press [LOAD] key to execute the load.

  • Page 10: Clip List Web Page

    Record” on ST600 Clip List web page to create the desired clip. *Record will start once “Create & Record” is pressed on web page or when Record key is pressed on the ST600 ST600-KIPRO User Manual Page 10 of 16...

  • Page 11: Function Table

    Select which Ki Pro to control by pressing either [1], [2], For control [3] or [4]. Red LED will indicate which Ki Pro is currently being controlled EE Mode [STOP] Pressing “STOP” key twice will put AJA Ki Pro into EE ST600-KIPRO User Manual Page 11 of 16...
  • Page 12 Press either [↑] or [↓] to step through the Cue Points. Select a Cue Once desired cue point is shown on ST600 LCD, press the Point [DOWN ARROW] ↓ [GOTO] key *Maximum of 20 cue points per Ki Pro ST600-KIPRO User Manual Page 12 of 16...

  • Page 13: Key Layout

    9. KEY LAYOUT ST600-KIPRO User Manual Page 13 of 16...

  • Page 14: Specifications

    Note: Serial and GPI/O connection are not supported at this time. REAR PANEL CONNECTORS POWER 1: +12V DC, 3.33Amps (Max) RESET Switch: Press to reset ST600-KIPRO ETHERNET: RJ45 100baseT, Full Duplex S1 Switch: Press and hold 10 seconds to reset IP address to 192.168.10.217 and...
  • Page 15 GPO 3 Common GPO 2 N.O. nearby Common Bus pins GPO 2 Common Common Bus There is no need to connect power supply Ground to GPO Common Bus GPO 1 N.O. connector GPO 1 Common ST600-KIPRO User Manual Page 15 of 16...

  • Page 16: Dnf Controls Limited Warranty

    11. DNF CONTROLS LIMITED WARRANTY DNF Controls warrants its product to be free from defects in material and workmanship for a period of one (1) year from the date of sale to the original purchaser from DNF Controls. In order to enforce the rights under this warranty, the customer must first contact DNF’s Customer Support Department to afford the opportunity of identifying and fixing the problem without sending the unit in for repair.

Table of Contents