Lucasey LC200WDA Installation Instructions

Articulating wall mount for up to 35lbs flat screens

Advertisement

LC200WDA INSTALLATION INSTRUCTIONS

Steps 1-4

5/16" Hex Bolt
VESA Plate
Important! Please read all warnings and cautions before installing the mount.
Caution: Improper installation of this mount may void the warranty on your monitor.
Caution: Installation should be performed by qualified installers only, using construction methods prescribed
by authorized architects or engineers that comply to all applicable codes and standards.
The maximum weight of monitor to be installed on the LC200WDA is 35lbs (15.9 kg)
Inspect all parts to make sure there is no shipping damage. Do not install if any parts are damaged.
Please call 1-800-LUCASEY or 1-510-534-1435 if you have any questions about this installation.
LC200WDA _Instructions (2/11)
Page 1 of 3
LC200WDA - Articulating Wall Mount
for up to 35Lbs Flat Screens
3/8" Hex Bolt
Wall Plate
(2pcs.) Covers
(4 pcs.) Cover Screws
©2011 Lucasey Manufacturing Corporation, Oakland, California
1. Remove the 5/16" Hex Bolt from the Wall Arm.
2. Remove the Cover Screws and Covers. Remove the 3/8" Hex Bolt from the
Wall Plate. Set asode the Wall Arm, VESA Plate, Covers and Hardware.
3. Use the Wall Plate as a template to mark and drill 1/8" pilot holes for each
of the Lag Screw locations. Check to make sure the Wall Plate is level before
marking and drilling the pilot holes. Drill the top and bottom holes first. Then,
drill the middle pilot hole with the Wall Plate level. (If installing in metal studs
or concrete, hardware kits can be purchased separately.)

Hardware List

1 ...
3/8-16 x 4-1/2" Hex Bolt
7 ...
3/8" Flat Washers
1 ....
3/8-16 Nylock Jam Nut
1 ...
5/16-18 x 2-1/4" Hex Bolt
2 ...
5/16" Flat Washers
2 ...
5/16-18 Nylock Nuts
1 ...
5/16-18 x 1-1/2" Socket Button Head Screw
2 ...
5/16" Belleville Washers
1 ...
1/4-20 x 1-1/2" Socket Button Head Screw
4 ...
1/4" Belleville Washers
1 ...
1/4-20 Nylock Nut
4 ...
#8-32 x 1/2" Phillips Self Tapping Screws
3 ...
#14 x 2-1/2" HWH Lag Screws
Monitor Attaching Hardware
6 ...
4mm x 25mm Set Screws
6 ...
5mm x 30mm Set Screws
6 ...
6mm x 30mm Set Screws
6 ...
4mm x 12mm Phillips Screws
6 ...
5mm x 12mm Phillips Screws
6 ...
6mm x 12mm Phillips Screws
12 ...
4mm Hex Nuts
12 ...
5mm Hex Nuts
12 ...
6mm Hex Nuts
36 ...
5mm Flat Washers
18 ...
1/4" Flat Washers
www.lucasey.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LC200WDA and is the answer not in the manual?

Questions and answers

Summary of Contents for Lucasey LC200WDA

  • Page 1 Caution: Installation should be performed by qualified installers only, using construction methods prescribed by authorized architects or engineers that comply to all applicable codes and standards. Monitor Attaching Hardware The maximum weight of monitor to be installed on the LC200WDA is 35lbs (15.9 kg) 6 ... 4mm x 25mm Set Screws 12 ...
  • Page 2 LC200WDA INSTALLATION INSTRUCTIONS Page 2 of 3 LC200WDA - Articulating Wall Mount for up to 35Lbs Flat Screens Step 4 3Pl. Lag Screws 4. Use the provided Lag Screws to securely fasten the Wall Plate to the wall. Tighten the top and bottom screws before tightening the middle screw to allow for some adjustment to make the Wall Plate level.
  • Page 3 LC200WDA INSTALLATION INSTRUCTIONS Page 3 of 3 LC200WDA - Articulating Wall Mount Steps 7-9 for up to 35Lbs Flat Screens 5/16" Hex Bolt 7. Align the hole on the Pivot Plate with hole on the Wall Arm. Pivot Plate 8. Replace the 5/16" Hex Bolt, washers, nylock nut.

Table of Contents