Table of Contents
Advertisement
12 one-touch speed dial numbers can be programmed into the memory of your telephone,
Each memory location can store a maximum of 32 digits.
®
STORING ONE-TOUCH SPEED DIAL NUMBERS
program
Eg : To
UNIDEN telephone number, 0295993577 into speed dial location 3
1.
Press the store button (Display shows NUMBER ?).
2.
Enter the phone number 0 2 9 5 9 9 3 5 7 7 using the keypad
3.
Press the store button (Display shows NAME ?)
I
4. *Enter the name U N
D E N using the keypad
(88 66 444 3 >> 33 66)
5.
Press the store button (display shows STORE TO?)
Press the speed dial button number 3
6.
The phone will beep and the display will show STORED
* If you do not
store a
want to
name, skip step
If you have to type in several letters (consecutively) contained in one button (i.e. D & E).
l
!
you need to press >> to move the cursor to the next space prior to pressing the button
again.
To add a space before another word, press 1 once. For more fhan one space, press >>.
l
Repeated pressing of the keypad digit '1' will step through the following symbols : -
Repeated pressing of any other keypad digit will step through the letters and number
l
associated with that key
Examples A=2, B=22, C=222, 2=2222, D=3, E=33, F=333 3=3333
!
Repeated pressing of the << or > > button will move the cursor backwards or
l
forwards to the position required.
When the cursor is flashing on top of any character you can press the delete button
l
to delete that character
.
Always store area code together with telephone numbers. This will be useful for CID
l
purposes.
®
PAUSE
During the memory storage procedure, you may wish to press the rdl/p button to insert a
pause between numbers. (This is sometimes useful for accessing a switch board, telephone
banking or long distance dialling).
Pressing rdl/p button more than once will increase the pause between digits.
Each time the rdl/p button is pressed, a 'P' will show on the LCD to indicate a 2 second pause
in the dialing sequence. Each pause counts as one digit.
®
MEMORY STORAGE CARD
When you have programmed a number
into the speed dial memory, you can write
the name of the person on the memory
storage card (supplied).
4
®
DIALING THE STORED NUMBERS
There are four different ways to dial a stored speed dial number, depending on your
preference.
Pick up the handset and press the desired memory button (1 - 12).
Press the speaker button and then press the desired memory
button (1 - 12).
Press the desired memory button (1 - 12), and check the LCD
shows the correct information. Press the dial button (the phone
enters speakerphone mode and dials the displayed number).
4. Press the desired memory button (1 - 12), and check the LCD
shows the correct information. Pick up the handset and then press
the dial button.
!
If you have selected a speed dial button that does not have a stored number, the
telephone will not dial.
For options 3 & 4, the LCD will show <EMPTY> if there is no number stored in the
memory button pressed.
®
CHAIN DIALING
' () & ,
On certain occasions (such as telephone banking), after dialing one number, you may wish to
dial another number without hanging up. This is known as chain dialing or cascade dialing.
Simply store the second number in another memory location and press the corresponding
speed dial button when required. In this way you can recall both numbers that are stored into
their own memory locations at the relevant times.
® CALLTIMER
Approximately 10 seconds after the handset is picked up,
or the speaker button is pressed, the call counter will begin
and show the elapsed time on the display screen.
LCD BACKLIGHT DISPLAY
The LCD has a back light that will turn on under the
following conditions;
Any incoming call
l
Picking up the handset
l
Pressing any button
l
!
The backlight will switch off automatically approximate/y 15 seconds after the last activity
The AC Adpator must be plugged into the unit to enable BACK LIGHT to work.
Hide quick links:
Advertisement
Table of Contents
