INTRODUCTION Congratulations on the purchase of your Uniden FP101 Telephone. The FP101 has been designed and engineered to exacting standards for reliability, long life and outstanding performance. To obtain the full benefit from your new telephone, please read this Operating Guide thoroughly.
Wall Mounting ........14 Using your FP101 ........15 Memory Dial Numbers .
Page 4
CONTENTS Accessing Call Waiting (New Zealand Model only) ..18 Accessing Call Waiting (Australian Model only) ..18 Mute .........19 Placing a Call on Hold .
IMPORTANT INFORMATION When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3.
IMPORTANT INFORMATION 9. Unplug this product and refer servicing to qualified service personnel under the following conditions: A. If liquid has been spilled into the product. B. If the product has been exposed to rain or water. C. If the product does not operate normally when following the operating instructions.
PARTS CHECKLIST (For New Zealand Model) Curly Cord Base Unit Handset Telephone Line Cord Wall Mounting Bracket FP101 with Pre-Programmed 5+15 Memory Operating Guide Feature Phone Series • 2 x Wall Mounting Memory Storage Card Operating Guide Screws and Wall Plugs...
PARTS CHECKLIST (For Australian Model) Curly Cord Base Unit Handset Telephone Line Cord Wall Mounting Bracket and Plug FP101 with Pre-Programmed 5+15 Memory Operating Guide Feature Phone Series • 2 x Wall Mounting Memory Storage Card Operating Guide Screws and Wall Plugs...
FEATURES • Pre-Programmed Feature Buttons Instant access to some of Telecom’s / Telstra’s most popular network service features* have been factory programmed into this telephone for your convenience. * Some of these services will require subscription. • 15 One Touch Speed Dial Buttons Your most important numbers can be programmed into the memory, for one touch speed dialing.
Page 10
FEATURES • Hearing Aid Compatible Inductive transducer coil handsets provide hearing aid compatibility. • Status LED Bright red LED provides visual indication and differentiation for calls 'In Use' or 'On Hold'. • Call LED Bright red LED provides visual indication of an incoming call. •...
FUNCTIONS NEW ZEALAND MODELS Button Button Button Button Button 6. One Touch Speed Dial Buttons 7. Memory Storage Card AUSTRALIAN MODELS Button Button Button Button Button 6. One Touch Speed Dial Buttons 7. Memory Storage Card NOTE: If required the Memory Storage Card can be turned over to give 20 One Touch memory buttons, as shown below...
Page 12
FUNCTIONS Button Button Button Button 12. Handset Retainer Tab Button 14. Telephone Number Card 15. Numeric Keypad 16. call LED 17. status LED Button 20. Not used 21. tone Slide Switch 22. Telephone Line Jack 23. ringer Volume Switch (Hi/Med/Low) 9 10 Button...
INSTALLATION HANDSET CORD CONNECTION Plug one end of the Handset Cord (curly) into the Handset and the other end into the jack on the side of the telephone. TELEPHONE LINE CORD CONNECTION Plug one end of the line cord (straight) into the telephone line jack on the back of the telephone and the other end into the wall outlet.
INSTALLATION WALL MOUNTING You can mount your phone directly on a wall. Before mounting your phone, consider the following: • Select a location away from electrical cables, pipes or other items behind the mounting location that could cause a hazard when inserting screws into the wall.
USING YOUR FP101 MEMORY DIAL NUMBERS 20 one touch speed dial numbers can be stored into the memory of your telephone. NOTE: There are 5 x Pre-Programmed memories and 15 x One Touch Memories. Each memory location can store a maximum of 32 digits.
USING YOUR FP101 PAUSE During the memory storage procedure you may enter a 4 second delay between numbers (for accessing a switchboard, or long distance service) by pressing the button on the Handset at the point in the number sequence you wish to pause.
USING YOUR FP101 ADJUSTING THE RINGER VOLUME CONTROL While the phone is ringing, you can adjust the ringer volume of your telephone by moving the ringer switch to the desired low/medium/high position. ADJUSTING THE RINGER TONE CONTROL While the phone is ringing, you can adjust the Ringer Tone of your telephone by moving the tone slide control to the desired position.
USING YOUR FP101 PLACING A TELEPHONE CALL 1. Remove the Handset from the Base. 2. Press the keypad buttons to dial the phone number you want. 3. After you have completed the phone call, place the Handset back on the Base.
USING YOUR FP101 MUTE Press and hold down the allowing private and confidential conversations in the same room without the call- ing party hearing. Release the with the calling party. PLACING A CALL ON HOLD 1. To place a call on hold, press the flash red and you can hang up.
USING YOUR FP101 Pick up the handset, listen for the dial tone, then press the The telephone will automatically dial the access code ‘161’ and will enable ‘immediate call diversion’ to the number you have assigned the divert to. Wait for the ‘confirmation tone’...
USING YOUR FP101 Call Back When the party you are calling is engaged or doesn’t answer, hang up. Pick up the handset, then press the The telephone will automatically dial the access code *’51’ to enable the ‘auto callback’ feature. Listen for an interrupted dial tone and hang up.
USING YOUR FP101 USING THE PRE-PROGRAMMED FEATURE BUTTONS (Australian Model Only) Instant access to some of Telstra’s most popular network service features have been factory programmed into this telephone for your convenience. Block CID Each time you make a call, your telephone number is automatically forwarded to the party you are calling (unless your number is a silent number).
USING YOUR FP101 NOTE: Until you cancel the ‘Call Forward No Answer’ diversion, (use all incoming calls will be diverted after 20 seconds (approximately 7 or 8 rings). Divert Off To cancel ‘Call Forward No Answer’ to another number. Pick up the handset, press the The telephone will automatically dial the access code ‘#61#’...
Page 24
USING YOUR FP101 NOTE: There is a monthly fee using the Message Bank service. For subscription and further information about Message Bank please call 1800 052 052 (this is a free call unless from a mobile phone). If you live outside the Sydney area, you will need to re-program the button as follows;...
TROUBLESHOOTING If your Telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact Uniden Customer Service for assistance. New Zealand: 0800 4 UNIDEN 4 864336 Australia: 1800 632 789 Problem Can’t make or receive calls.
SPECIFICATIONS Specifications for New Zealand Model Compliance Size: Weight: Specifications, Features and availability of Optional Accessories shown are typical and subject to change without notice. NOTE: FOR USE OF THIS DEVICE IN NEW ZEALAND 1. The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network.
Uniden, (C) Improperly installed, (D) Repaired by someone other than an authorised Uniden Repair Agent for a defect or malfunction covered by this warranty, (E) Used in conjunction with any equipment or parts or as a part of a system not manufactured by Uniden.