Tufline T4X Series Operator's Manual

Tandem disc

Advertisement

O P E R A T O R ' S M A N U A L
T4X SERIES
TANDEM DISC
www.monroetufline.com
14313
2/22/2010

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T4X Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Tufline T4X Series

  • Page 1 O P E R A T O R ' S M A N U A L T4X SERIES TANDEM DISC www.monroetufline.com 14313 2/22/2010...
  • Page 2: Introduction Ii

    Use only genuine Tufline service parts. Substitute parts will void the warranty and may not meet stan- dards required for safe and satisfactory operation. Record the model number and serial number of your...
  • Page 3: Table Of Contents

    TABLE OF CONTENTS INTRODUCTION ..........ii SPECIFICATIONS .
  • Page 4: Specifications

    GENERAL INFORMATION The purpose of this manual is to assist you your particular situation. in operating and maintaining your TUFLINE The illustrations and data used in this DISC. Read it carefully. It furnishes infor- manual were current at the time of print- mation and instructions that will help you ing.
  • Page 5: Safety Decals 2

    SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH Replace Decals Immediately If Damaged! Check that all safety decals are installed and in good condition. Replace if decals are worn or damaged. Safety Decals 2...
  • Page 6: Safety Rules

    SATETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and death. manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped • Keep hands and body away from pressurized out by an operator’s single careless act.
  • Page 7 SATETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! PREPARATION (cont’d) sharply, kinked, frayed, pinched, or come into • Use extreme care and reduce ground speed contact with any moving parts. Operate move- on slopes and rough terrain. able components through full operational range to check clearances.
  • Page 8 SATETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! OPERATION (cont’d) • Air in hydraulic systems can cause erratic • Keep hands, feet, hair, and clothing away from operation and allows loads or equipment compo- equipment while engine is running. Stay clear of nents to drop unexpectedly.
  • Page 9 SATETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! MAINTENANCE (cont’d) damage. Hoses must not be twisted, bent sharp- moveable parts even when the engine has been ly, kinked, frayed, pinched, or come into contact turned off. Hydraulic system leak down, hydrau- with any moving parts.
  • Page 10: Parts Catalog

    FIG. 1 7 Parts Catalog...
  • Page 11: Operation 8

    Operation Safety is a primary concern in the design and unexpectedly and cause severe injury or manufacture of our products. Unfortunately, our death. efforts to provide safe equipment can be wiped • Service work does not require going under- out by an operator’s single careless act. neath.
  • Page 12: Adjustment

    While making your initial run, observe the disc The gang angles on the T4X series disc are closely as it is traveling. It should be level from adjustable. The unit should be lifted two to three the front to rear as it travels.
  • Page 13: Maintenance 10

    Owner Service Gang Assembly for Maintenance WARNING WARNING • NEVER GO UNDERNEATH EQUIPMENT. Never place any part of the body underneath • When performing maintenance or repairs equipment or between moveable parts even make sure the equipment is in the lowered when the engine has been turned off.
  • Page 14: Optional Equipment

    11 Optional Equipment...
  • Page 15 Optional Equipment 12...
  • Page 16 13 Optional Equipment...
  • Page 17: Bolt Size And Bolt Torque Chart 14

    SAE TORQUE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for stan- dard SAE bolts. THIS IS STANDARD FOR SAE GUIDE FOR ALL MONROE TUFLINE IMPLEMENTS MARKING ON HEAD Diameter Wrench SAE 2 SAE 5 SAE 8...
  • Page 18: Trouble Shooting

    Gang Adjustment Trouble Shooting 1. Unit not tracking or is fishtailing A. Adjust top link to increase weight on the rear of the disc. B. Disc assembled incorrectly. Refer to assembly in- structions. 2. Unit not tracking: skipping, jumping, and A.
  • Page 19: Warranty 16

    Monroe-Tufline’s obligation under this Warranty is limited to, at Monroe-Tufline’s option, the repair or replacement, free of charge, of the product if Monroe-Tufline, in its sole discretion, deems it to be defective or in noncompliance with this Warranty. Such parts shall be provided by the selling dealer to the user during regular working hours. If...
  • Page 20 Monroe-Tufline’s obligation under this Warranty is limited to, at Monroe-Tufline’s option, the repair or replace- ment, free of charge, of the product if Monroe-Tufline, in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The selling dealer shall provide such parts to the user during regular work- ing hours.
  • Page 21: Warranty Registration 18

    ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ FILL OUT REGISTRATION CARD BELOW AND MAIL TO: MONROE TUFLINE Attn; Owner Registration PO BOX 7755 Columbus, MS 39705 ------------------------------------------------------------------- OWNER WARRANTY REGISTRATION NAME___________________________ ADDRESS / CITY / STATE__________________________ _________________________ DEALER NAME ______________________________ CITY / STATE_________________________...
  • Page 22 PART NO. 14313 MONROE TUFLINE MFG. CO., INC. PO BOX 7755 / 2219 TUFLINE LANE COLUMBUS, MS 39705-0004 (662)328-8347 www.monroetufline.com © 2008 Monroe Tufline Manufacturing, Inc. All Rights Reserved...

Table of Contents