Download
Share
Print this page
Dynojet POWER COMMANDER V Installation Instructions
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Automobile Electronics
  5. Power commander V
  6. Installation instructions

Dynojet POWER COMMANDER V Installation Instructions

Fuel and ignition. 2015-2018 polaris ranger 570
Hide thumbs Also See for POWER COMMANDER V:
1
2
3
4
5

Advertisement

Quick Links

Download this manual
FUEL AND IGNITION
2015-2018 Polaris Ranger 570
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
I19-035
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro strips
1
Alcohol swab
1
Posi-tap
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
THE LATEST POWER COMMANDER
SOFTWARE AND MAP FILES CAN BE
DOWNLOADED FROM OUR WEB SITE AT:
www.powercommander.com
2015-2018 Polaris Ranger 570 - PCV F/I - 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the POWER COMMANDER V and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Dynojet POWER COMMANDER V

Summary of Contents for Dynojet POWER COMMANDER V

  • Page 1 USB Cable FUEL AND IGNITION Installation Guide Power Commander Decals 2015-2018 Polaris Ranger 570 Dynojet Decals I n s t a l l a t i o n I n s t r u c t i o n s Velcro strips Alcohol swab Posi-tap THE IGNITION MUST BE TURNED...

  • Page 2: Usb Connection

    POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Switch Input #1 by default.) Shifter- (Input 1 or 2) These inputs are for use with the Dynojet quickshifter. Insert the wires from the CRANK Dynojet quickshifter into the SHIFTER inputs. ANALOG The polarity of the wires is not important. (Set to Switch Input #2 by default.) SPEED EXPANSION PORTS 1 & 2 INPUT 2 (Grnd)
  • Page 3 FIG.A Raise the passenger side bench seat and lift the cargo bed. Use the supplied Velcro strips to secure the PCV module under the seat next to the fuse box (Fig. A). Clean the surface area with the supplied alcohol swab prior to applying the Velcro. Route the PCV wiring harness out of this compartment and towards the engine. FIG.B Unplug Locate the vehicle’s Ignition Coil (just left of the engine) and unplug the BLACK 2-pin connector from it (Fig. B). FIG.C Plug the pair of BLACK 2-pin connectors with GREEN colored wires of the PCV wiring harness in-line of the Ignition Coil and the stock wiring harness (Fig. C). Continue routing the rest of the PCV wiring harness towards the throttle body. I19-035 www.powercommander.com 2015-2018 Polaris Ranger 570 - PCV F/I - 3...
  • Page 4 FIG.D Locate and unplug the stock wiring harness from the Fuel Injector (Fig. D). Unplug The Fuel Injector is located at the top of the intake plenum just beneath the fuel rail at the rear of the cylinder head. FIG.E Plug the pair of PCV wiring harness leads with ORANGE colored wires in-line of the Fuel Injector and the stock wiring harness (Fig. E). FIG.F Locate the stock BLACK 6-pin Throttle Body Servo connector on the Throttle Body Servo just rear of the Fuel Injector. 10 Use the supplied Posi-tap to attach the single unterminated GREY wire of the PCV wiring harness to the stock GREEN/RED wire (pin position #1) of the stock Throttle Body Servo connector (Fig. F). 11 Continue routing the harness towards the right side of the engine. I19-035 www.powercommander.com 2015-2018 Polaris Ranger 570 - PCV F/I - 4...
  • Page 5 FIG.G 12 Locate and unplug the stock connector pair from the vehicle’s Crank Position Unplug Sensor (Fig. G). You can trace the cable coming out of the top of the right side flywheel cover to this BLACK 3-pin connector pair. FIG.H 13 Plug the pair of PCV wiring harness connectors with BROWN colored wires in-line of the stock Crank Position Sensor connectors (Fig. H). 14 Secure the PCV ground wire with the small ring lug to the engine case bolt shown in Figure H. Ground 15 Lower the cargo bed and the bench seat. I19-035 www.powercommander.com 2015-2018 Polaris Ranger 570 - PCV F/I - 5...