Dynojet Power Commander V Installation Instructions
2011-2012 can-am commander 800
Hide thumbs
Also See for Power Commander V:
- Installation instructions manual (9 pages) ,
- Installation manual (9 pages) ,
- Installation instructions and owner's manuals (8 pages)
Advertisement
Quick Links
2011-2012 Can-Am Commander 800
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
25-007
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
CD-ROM
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro
1
Alcohol Swab
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
YOU CAN ALSO DOWNLOAD THE
POWER COMMANDER SOFTWARE AND
LATEST MAPS FROM OUR WEB SITE AT:
www.powercommander.com
11-12 Can-Am Commander 800 PCV - 1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Dynojet Power Commander V
Summary of Contents for Dynojet Power Commander V
- Page 1 2011-2012 Can-Am Commander 800 Installation Guide Power Commander Decals I n s t a l l a t i o n I n s t r u c t i o n s Dynojet Decals Velcro Alcohol Swab THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION!
-
Page 2: Usb Connection
Do NOT connect anything to this port unless wire into the hole of the PCV until is stops and then instructed to do so by Dynojet. It is used to tighten the screw. Make sure to reinstall the rubber transfer crank trigger data from one module to plug. - Page 3 FIG.A Remove the center console, glove compartment, ignition switch board, and both passenger side engine compartment cover panels. The motor compartment will be exposed as shown in Figure A. FIG.B Using the supplied velcro, secure the PCV to the driver side engine cover as shown in Figure B. Make sure to clean both surfaces with the alcohol swab before attaching. Attach the ground wire from the PCV to the negative side of the battery as shown in Figure B. FIG.C Route the PCV harness over the engine cover and route the harness along the intake plenum as shown in Figure C. 25-007 www.powercommander.com 11-12 Can-Am Commander 800 PCV - 3...
- Page 4 FIG.D Locate the fly by wire throttle servo and unplug the six-pin connector. The fly by wire throttle servo is located on the passenger side of the intake plenum. Attach the connectors from the PCV harness in line with stock wiring harness and the servo unit. FIG.E Unplug the three-pin coil connector. This connector is located on the coil under the center console on the left side. Attach the connectors from the PCV harness to the stock wiring harness and the coil connector. FIG.F 10 Locate the two-pin crank connector. This connector is located beneath the intake plenum on the drivers side of the engine. 11 Attach the connectors from the PCV harness to the stock wiring harness and the crank connector. 25-007 www.powercommander.com 11-12 Can-Am Commander 800 PCV - 4...
- Page 5 FIG.G 12 Locate the fuel injectors above the engine as shown in Figure G. FIG.H 13 Attach the connectors from the PCV to the stock wiring harness and the fuel injectors. • orange wires connect to the front cylinder • yellow wires connect to the rear cylinder 14 Replace the passenger side engine compartment cover panels, ignition switch board, glove compartment, and center console. 25-007 www.powercommander.com 11-12 Can-Am Commander 800 PCV - 5...
Need help?
Do you have a question about the Power Commander V and is the answer not in the manual?
Questions and answers