Page 1
DAEDONG DK752C/DK902C/DK1002C, it is the policy of DAEDONG tractor to provide an owner's manual which includes helpful information about tractor safety, operation and mainte- nance. If the information you seek is not found in this manual, your DAEDONG tractor dealer will be happy to help you.
Page 2
SAFETY AND VEHICLE DAMAGE WARNING This manual includes information titled as WARNING, CAUTION, IMPORTANT and NOTE. These titles indicate the following: This indicates a situation that could result in harm, serious injury or death to you or other persons if the warning is not heeded.
Page 3
ABBREVIATION LIST ABBREVIATIONS DEFINITIONS Four Wheel Drive American Petroleum Institute ASAE American Society of Agricultural Engineers, USA ASTM American Society of Testing and Materials, USA Feet Per Minute Hi-Lo High Speed-Low Speed Hydrostatic Transmission Meters Per Second P.T.O Power Take Off RH/LH Right-hand and Left-hand sides are determined by facing in the direction of forward travel ROPS...
Page 4
UNIVERSAL SYMBOLS Various universal symbols have been used on the instruments and controls of your DAEDONG tractor. Be- low is a list of the universal symbols and their meanings. Fuel-level Headlight-low beam Preheat Engine coolant-temperature Headlight-high beam QT lamp Parking brake...
Page 5
TABLE OF CONTENTS SAFETY PRECAUTIONS ........... SERVICING OF TRACTOR ..........SPECIFICATIONS ............... DESCRIPTION OF OPERATING SYSTEM ......SECTION OPERATION ............... PERIODIC SERVICE ............STORAGE ................TROUBLESHOOTING ............INDEX.................. M39-마력업-AU-00.indd 5 2009-02-04 오후 9:14:12...
Page 6
M39-마력업-AU-00.indd 6 2009-01-23 오후 4:30:29...
DK752C / DK902C / DK1002C BEFORE OPERATING THE TRACTOR A careful operator is the best oper- ator. Most accidents can be avoid- ed by observing certain precautions. To help prevent accidents, use these safety precautions, and pay attention to the job at hand. If you can prevent an accident, your time will have been well spent.
Page 9
SAFETY PRECAUTIONS S42O103a S42O104a S42O105a 9. Never operate this tractor or 12. Never start the engine while 16. All persons using the tractor any other agricultural equipment standing on the ground. should have knowledge of its while under the influence of alco- proper operation and should read 13.
Page 10
DK752C / DK902C / DK1002C 20. For your safety ROPS with a seat belt is recommended for most applications. NOTE Always use seat belt when the tractor is equipped with a ROPS and CAB. All tractors must have CAB or ROPS.
SAFETY PRECAUTIONS OPERATING THE TRACTOR S42O108a S42O109a S42O110a 1. Avoid accidental contact with gear 2. Do not park your tractor on a 3. Do not operate your tractor in shift levers while the engine is run- steep incline, and remember to an enclosed building without the ning.
Page 12
DK752C / DK902C / DK1002C S42O111a S42O112a S42O113a (1) Drawbar 4. Make sure that all pressure lines 6. If the front end of the tractor rises 7. Always use the proper ballast are tight before starting the tractor. up when using heavy implement,...
Page 13
SAFETY PRECAUTIONS 9. Do not leave equipment in the raised position when the vehicle is stopped or unattended. 10. When using implements or at- tachments with your tractor you should first read their respective owner's manual. Always keep safe operation procedures in mind.
SAFETY PRECAUTIONS PARKING THE TRACTOR OPERATING THE P.T.O 4. Observe all local traffic and safe- ty rules. 5. If using headlights, dim them when meeting another vehicle. 6. Drive at speeds that allow you to maintain control at all times. 7.
DK752C / DK902C / DK1002C USING 3-POINT HITCH SERVICING THE TRACTOR S42O121a S42O122a S42O123a (1) 3-Point Hitch Lowering Speed Knob (A) "SLOW" (B) "FAST" 3. Before installing or using P.T.O 1. Use the 3-point hitch only with When servicing your tractor park on...
Page 17
SAFETY PRECAUTIONS S42O124a S42O125a S42O126a 2. Allow the tractor time to cool off 6. Do not remove the radiator cap 7. When working with your tractor's before servicing any part that may while the coolant is hot. When electrical components always dis- have become hot while the tractor cool, slowly rotate the cap to the connect the battery cables.
Page 18
DK752C / DK902C / DK1002C S42O127a S42O128a S42O129a (1) Cardboard (2) Hydraulic Line (3) Magnifying Glass 9. Tire mounting should be done by 12. Always ensure that wheel bolts 14. Fluid escaping from pinholes may have been tightened to the spec- qualified professionals, with the be invisible.
Page 19
SAFETY PRECAUTIONS S42O130a 15. Keep environmental pollution in mind. When replacing coolant or oil, dispose of it the right way. 16. Be sure to follow state and feder- al law when disposing of engine oil, transmission oil, fuel, coolant and batteries. M39-마력업-AU-01.indd 13 2009-01-23 오후...
Page 21
SAFETY PRECAUTIONS (1) Part No. : T4818-52142 (3) Part No. : E6500-51102 (5) Part No. : T2615-52131 (2) Part No. : T2615-55112 (4) Part No. : T4938-52351 (6) Part No. : T4837-52121 M39-마력업-AU-01.indd 15 2009-01-23 오후 6:18:16...
Page 22
DK752C / DK902C / DK1002C (7) Part No. : T2325-50743 (9) Part No. : T2445-50724 (11) Part No. : T4836-51091 (8) Part No. : T4938-52321 (10) Part No. : T4837-51181 (12) Part No. : T4938-53551 M39-마력업-AU-01.indd 16 2009-01-23 오후 6:18:18...
Page 23
SAFETY PRECAUTIONS (13) Part No. : T2615-54112 (15) Part No. : T4938-52411 (17) Part No. : T2615-53561 (14) Part No. : T4938-52361 (16) Part No. : T4625-52351 (18) Part No. : T4837-51191 M39-마력업-AU-01.indd 17 2009-01-23 오후 6:18:20...
Page 24
MEMO MEMO M39-마력업-AU-01.indd 18 2009-01-23 오후 6:18:20...
Page 25
SERVICING.OF.TRACTOR SERVICING..............2-2 M39-마력업-AU-02.indd 1 2009-01-23 오후 4:31:15...
Page 26
DK752C / DK902C / DK1002C SERVICING Before using implements not sold by a DAEDONG.dealer, verify oper- ational a safety features of the im- plement. Always operate equipment in the manner it was designed to be used. Identification No. Engine.Serial.No..
Page 32
DK752C / DK902C / DK1002C TRAVELING.SPEED * At rated engine speed with Std. tires. [FORWARD] km/h(m/h) Operating.the.lever MODEL Main Range Main 0.76(0.47) 0.99(0.61) Creep (C) 1.29(0.80) 1.68(1.04) 2.07(1.28) 2.71(1.68) Low (L) 3.52(2.18) 4.60(2.85) Forward 5.51(3.42) 7.20(4.46) Middle (M) 9.37(5.81) 12.23(7.58) 15.96(9.90)
Page 33
SPECIFICATIONS [REVERSE] km/h(m/h) Operating.the.lever MODEL Main Range Main 0.61(0.38) 0.79(0.49) Creep (C) 1.03(0.64) 1.35(0.84) 1.66(1.03) 2.17(1.35) Low (L) 2.82(1.75) 3.68(2.28) Forward 4.41(2.73) 5.77(3.58) Middle (M) 7.51(4.66) 9.80(6.08) 12.79(7.93) 16.73(10.37) High (H) 21.75(13.49) 28.39(17.60) M39-마력업-AU-03.indd 7 2009-02-16 오후 4:54:31...
Page 34
DK752C / DK902C / DK1002C IMPLEMENT.LIMITATIONS This KIOTI tractor has been thoroughly tested for proper performance with implements sold or approved by KIOTI. Use with implements which are not sold or approved by KIOTI and which exceed the maximum specifications listed below, or which are otherwise unfit for use with this KIOTI tractor may result in malfunctions or failures to the tractor, damage to other property and injury to the operator or others.
Page 35
2,134mm (84in) maximum or rated for 65 PTO HP w/FWA NOTE. : This is a sample of attachments commonly used. Before purchasing or using any attachment on a DAEDONG product, please review the specifications to determine if it is a compatible product. Damages or failures due to improper use of compatibility issue will not be covered by warranty.
Page 36
2,438 mm (96in) maximum or rated for 80 PTO HP w/FWA NOTE. : This is a sample of attachments commonly used. Before purchasing or using any attachment on a DAEDONG product, please review the specifications to determine if it is a compatible product. Damages or failures due to improper use of compatibility issue will not be covered by warranty.
Page 37
DeScriPtion of oPeratinG SyStem exterior view ............4-2 SwitcheS ..............4-3 inStrument Panel ..........4-6 oPeratinG the controlS ........4-11 DeScriPtion of cab oPeratinG SyStem ..4-20 heater anD air-conDitioner ......4-26 M39-마력업-AU-04.indd 1 2009-01-23 오후 6:05:11...
DESCRIPTION OF OPERATING SYSTEM SwitcheS (1) Panel (2) Horn Switch (3) Turn Signal Switch/Head Light Switch (4) Hazard Lamp Switch (5) Hour Meter (6) PTO Auto/Manual Switch (7) Key Switch S43O402A M39-마력업-AU-04.indd 3 2009-01-23 오후 6:05:17...
Page 40
DK752C / DK902C / DK1002C Key Switch turn SiGnal / heaD liGht Switch and the starter will start to rotate and the engine should start. Release the key switch and it will return to the ON position. A key position for stopping the en- gine.
Page 41
DESCRIPTION OF OPERATING SYSTEM hazarD lamP Switch Pto chanGe Switch (manual / auto) off : Headlight is turned OFF : Low beam headlight is turned : U p p e r b e a m h e a d l i g h t i s turned ON : Direction indication lamp is turned ON...
Page 43
This indicates the time as the rated revolution number of the engine. if the gauge reaches the red zone, immediately turn off the engine and have it inspected at your local DaeDonG ser- vice facility or dealer. M39-마력업-AU-04.indd 7 2009-01-23 오후 6:05:23...
Page 44
DK752C / DK902C / DK1002C enGine oil PreSSure 4wD lamP warninG lamP caution if the oil level is below the specified range, the engine can sieze. S42O411A S42O413A This lamp is turned On when the en- This lamp indicates 4WD.
Page 45
DESCRIPTION OF OPERATING SYSTEM battery charGinG lamP air filter warninG lamP heaD liGht hiGh beam lamP S42O414A S42O415A S42O416A This lamp is turned On when the This lamp illuminates when the air fil- This lamp is On when the head light starting switch is turned On before ter is clogged by dust etc.
Page 46
DK752C / DK902C / DK1002C Glow PluG inDicator Pto inDicator ParKinG braKe warninG lamP S42O417A S42O418A S42O419A This lamp indicates preheat cycle is This indicates ON/OFF of the PTO When the parking brake is actuated, operating. The preheat cycle is con- clutch.
DESCRIPTION OF OPERATING SYSTEM oPeratinG the controlS (1) Shuttle Shift Lever (2) PTO Change Lever (3) Range Shift Lever (4) Parking Brake (5) Main Shift Lever (6) Hand Throttle Lever (7) Joy-stick Lever (8) Position Control Lever (9) Draft Control Lever (10) PTO Switch (ON/OFF) (11) Double Acting Lever (A, B) (12) Double Acting Lever (C, D)
Page 48
DK752C / DK902C / DK1002C main Shift lever ranGe Shift lever Shuttle Shift lever S42O423A S42O424A S42O425A There are 4 speeds available in each Rapid shifting between forward/re- caution range, (1) being lowest to (4) high- verse can shorten the life of and/or to change the shift levers, est on the main shift lever.
Page 49
DESCRIPTION OF OPERATING SYSTEM Pto Switch (on / off) Pto chanGe lever Pto Selection lever S42O426A S42O427A S42O428A (1) PTO switch (1) PTO Change Lever (1) PTO Selection Lever (A) Independent PTO (B) Ground Speed PTO - ON - OFF Shift the PTO switch to OFF position You can select independent PTO op- Shift...
Page 50
DK752C / DK902C / DK1002C clutch PeDal inDePenDent Pto imPortant The independent PTO mode is used t h e c l u t c h p e d a l m u s t b e for normal PTO operations. It op-...
Page 51
DESCRIPTION OF OPERATING SYSTEM braKe PeDal tiltinG SteerinG lever (riGht anD left) 3. When operating the tractor on roads,always be sure to interlock the left and the right brake ped- als. Do not forget to observe this precaution, stepping on only one brake while operating on roads can cause an accident resulting in personal injury or death.
Page 52
DK752C / DK902C / DK1002C ParKinG braKe lever foot throttle hanD throttle lever S42O433A S42O434A S42O435A (1) Parking Brake Lever (1) Foot Throttle (1) Foot Throttle (2) Hand Throttle Lever (A) Pull (B) Push Decrease Increase When the parking brake is pulled up-...
Page 53
DESCRIPTION OF OPERATING SYSTEM Differential locK PeDal Seat caution w h e n u s i n g t h e d i f f e r e n - tial lock, decrease the engine rPm. when the pedal is de- pressed, the differential is en- gaged, and when the pedal is released, the differential is dis-...
Page 54
DK752C / DK902C / DK1002C PoSition / Draft control leverS SeatbacK reclininG aDjuSt- PoSition control ment The position control lever main- To adjust the seatback reclining an- tains a setting depth during work. Af- gle, lean forward and pull the lever ter setting the handling position of upwards.
Page 55
DESCRIPTION OF OPERATING SYSTEM joySticK lever mixeD control 1. Connect 2 male couplers coming from the loader bucket cylinder to Lower the attachment to the desired the port E & F couplers in front of depth using the draft control lever the tractor cabin.
DK752C / DK902C / DK1002C DeScriPtion of cab oPeratinG SyStem internal aDjuStment SyStem S42O448A (1) Air Grill (6) Air Inlet (11) Wiper Operating Switch (Front) (2) Speaker (7) Ashtray (12) Wiper Operating Switch (Rear) (3) Heater/Air conditioner Switch (8) Cigar Light...
Page 57
DESCRIPTION OF OPERATING SYSTEM external featureS of the rear winDow entrance S42O449A S42O450A S42O451A (1) Working Lamp (Front / Rear) (1) Handle Of Rear Window (1) Button (2) Handle (2) Rear View Mirror (2) Button (3) Wiper 1. The cap is designed for comfort If you lightly push rear window while de- Pressing the button of the handle will and convenience.
Page 58
DK752C / DK902C / DK1002C worKinG liGht wiPer (front / rear) S42O452A S42O453A S42O454A (1) Side Windows (1) Working Light Switch (Front) (1) Wiper Operating Switch (Front) (2) Working Light Switch (Rear) (2) Wiper Operating Switch (Rear) (3) Working Light (Front / Rear)