Page 1
Business Networking Solution Installation Guide Unmanaged PoE+ Switch...
Page 3
Remind to take notice. The note contains the helpful information for a better use of the product. Related Document This Installation Guide is also available in PDF on our website. To obtain the latest documentation and product information, visit the official website: https://www.tp-link.com.
IP telephones, wireless LAN access points, network cameras, network hubs, embedded computers and so on. Appearance Front Panel ■ The front panels of TL-SL1218P and TL-SL1218MP are shown as the following figure. Figure 1-1 Front Panel of TL-SL1218P LEDs Switches...
Page 6
On: Running at 10/100 Mbps but no activity. Flashing: Running at 10/100 Mbps and is transmitting or receiving data. Off: No device is linked to the corresponding port. Port 17–18/18F (for TL-SL1218P) Link/Act Port 17–18/17F–18F (for TL-SL1218MP) Green On: Running at 1000 Mbps but no activity.
Page 7
PDs. The maximum PoE power for each PoE port is 30 W. The maximum PoE power for all PoE ports is 150 W (for TL-SL1218P)/250 W (for TL-SL1218MP). The ports can also connect to non-PoE devices, but only transmit data.
Page 8
Unmanaged PoE+ Switch Indication On: Total power supply ≥ 243 W. PoE Max Flashing: Total power supply ≥ 243 W and lasts for more than 2 minutes. Off: Total power supply ≤ 243 W. Switches Switch Indication Extend Mode switch 1–8, 9–16 and 17–24 can control the rate and power supply distance of corresponding ports.
Page 9
PE (Protecting Earth) cable of AC cord or with Ground Cable. For detailed lightning protection, go to https://www.tp-link.com/support, search the model number of your switch and go to the product Support web page, refer to the Lightning Protection Guide from the Related Documents: https://www.tp-link.com/us/configuration-guides/lightning_protection_guide/.
Unmanaged PoE+ Switch Chapter 2 Installation Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, contact your distributor. One Switch One Power Cord Two mounting brackets, eight This Installation Guide screws and four rubber feet Safety Precautions To avoid any device damage and bodily injury caused by improper use, you should observe the...
Page 11
Unmanaged PoE+ Switch Keep the equipment room at an appropriate level of temperature and humidity. Too much or too little humidity may lead to bad insulation, leakage of electricity, mechanical property changes, and corrosion. High temperatures may accelerate aging of the insulation materials, significantly shortening the service life of the device.
Use the signal SPD (Surge Protective Device) when wiring outdoor. ■ Note: For detailed lightning protection measures, go to https://www.tp-link.com/support, search the model number of your switch and go to the product Support web page, refer to the Lightning Protection Guide from the Related Documents: https://www.tp-link.com/us/configuration-guides/lightning_protection_guide/.
Page 13
Unmanaged PoE+ Switch Figure 2-1 Desktop Installation Feet Bottom of the Device Notch Rack Installation ■ To install the device in an EIA standard-sized, 19-inch rack, follow the instructions described below: 1. Check the efficiency of the grounding system and the stability of the rack. 2.
Unmanaged PoE+ Switch Chapter 3 Connection Ethernet Port Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shows. Figure 3-1 Connecting the RJ45 Port RJ45 Port RJ45 Cable SFP Port The following figure demonstrates the connection of SFP port to an SFP module. Figure 3-2 Inserting the SFP Module SFP Slot...
Unmanaged PoE+ Switch Power On Plug the negative connector of the provided power cord into the power socket of the device and plug the positive connector into a power outlet as the following figure shows. Figure 3-3 Connecting to Power Supply Note: The figure is to illustrate the application and principle.
PoE Port: Port 1–16 Total Power Supply: 250 W For TL-SL1226P PoE Port: Port 1–24 Total Power Supply: 250 W Switching Capacity 7.2 Gbps (for TL-SL1218P/TL-SL1218MP) Gbps (for TL-SL1226P) Mac Address Table Transfer Method Store-and-Forward Power Supply 100–240 VAC, 50/60 Hz Fan Quantity Operating Temperature 0 ℃...
Page 18
EU declaration of conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
Page 20
To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community. For technical support, the user guide and other information, please visit https://www.tp-link.com/support, or simply scan the QR code. If you have any suggestions or needs on the product guides, welcome to email techwriter@tp-link.com.cn.