Related Manuals for Nexen AIR CHAMP DPC-9T
Summary of Contents for Nexen AIR CHAMP DPC-9T
- Page 1 ® MEX (55) 53 63 23 31 MTY (81) 83 54 10 18 QRO (442) 1 95 72 60 ventas@industrialmagza.com DIST. AUTORIZADO Models DPC-9T and DPC-11T FORM NO. L-20070-E-0102...
- Page 2 DIST. AUTORIZADO In accordance with Nexen’s established policy of constant product improvement, the specifications contained in this manual are subject to change without notice. Technical data listed in this manual are based on the latest information available at the time of printing and are also subject to change without notice.
-
Page 3: Table Of Contents
® MEX (55) 53 63 23 31 MTY (81) 83 54 10 18 QRO (442) 1 95 72 60 ventas@industrialmagza.com DIST. AUTORIZADO TABLE OF CONTENTS Introduction ---------------------------------------------------------------------------------------------------------------------------------------- 1 Installation ---------------------------------------------------------------------------------------------------------------------------------------- 2 Air Connections --------------------------------------------------------------------------------------------------------------------------------- 4 Lubrication ----------------------------------------------------------------------------------------------------------------------------------------- 6 Operation ------------------------------------------------------------------------------------------------------------------------------------------ 6 Parts Replacement ----------------------------------------------------------------------------------------------------------------------------- 7 Replacement Parts ----------------------------------------------------------------------------------------------------------------------------- 9 Accessories ------------------------------------------------------------------------------------------------------------------------------------- 10... -
Page 4: Introduction
NOTES, CAUTIONS, and WARNINGS are not assembly becomes the driven unit. exhaustive. Nexen cannot possibly know or evaluate all conceivable methods in which service may be performed, When mounted on a continually running shaft, the inner... -
Page 5: Installation
Splined Hub (Item 1) (See Fig. 1). CAUTION FIGURE 1 Do not use a hammer to install Support Bushing. Nexen recommends a small arbor press. NOTE: On “DPC-9T” the Support Bushing fits flush with the end of the Splined Hub. - Page 6 ® MEX (55) 53 63 23 31 MTY (81) 83 54 10 18 QRO (442) 1 95 72 60 ventas@industrialmagza.com DIST. AUTORIZADO NOTE: Do not use lubricants or thread locking compounds on Pull-Up Bolts. 5. Measure runout of Motor Shaft. Runout must not exceed 0.002 T.I.R.
-
Page 7: Air Connections
® MEX (55) 53 63 23 31 MTY (81) 83 54 10 18 QRO (442) 1 95 72 60 ventas@industrialmagza.com DIST. AUTORIZADO AIR CONNECTIONS SHAFT END MOUNTING. 1. Install two Elbow Fittings (Item 20) into the Rotary Air Union Cap (Item 25) (See Fig. 4). 2. - Page 8 ® MEX (55) 53 63 23 31 MTY (81) 83 54 10 18 QRO (442) 1 95 72 60 ventas@industrialmagza.com DIST. AUTORIZADO 6. Install an Adaptor Fitting (Item 19) and Elbow Fitting (Item 20) into each air inlet of the Piston/Drive Disc (Item 2).
-
Page 9: Lubrication
NOTE: Use a low viscosity petroleum base oil, such as “DPC” Clutch is with an air line lubricator. Available from SAE10. Synthetic lubricants are not Nexen, the lubricator injects oil into the pressurized air, recommended. forcing a constant oil mist into the air chamber. -
Page 10: Parts Replacement
DIST. AUTORIZADO PARTS REPLACEMENT TABLE 6 CAUTION Recommended Tightening Torques The Nexen “DPC” Clutch has been balanced at the factory. During disassembly, mark components with chalk alignment marks to insure correct alignment, and balance as the e t I . t f . - Page 11 ® MEX (55) 53 63 23 31 MTY (81) 83 54 10 18 QRO (442) 1 95 72 60 ventas@industrialmagza.com DIST. AUTORIZADO 5. Slide the Piston/Drive Disc (Item 2) off of the Splined Hub (Item 1) (See Fig. 8). 6. Remove the Retaining Ring (Item 10) (See Fig. 8). Special attention should be exercised when working with retaining rings.
-
Page 12: Replacement Parts
(See Table 6). 8. Remove Retaining Ring (Item 18) (See Fig. 10). REPLACEMENT PARTS The Item or “Balloon” Number for all Nexen Products is When ordering replacement parts, specify model used for part identification on all Product Parts List, designation, item number, part description, and quantity. -
Page 13: Accessories
® MEX (55) 53 63 23 31 MTY (81) 83 54 10 18 QRO (442) 1 95 72 60 ventas@industrialmagza.com DIST. AUTORIZADO PARTS LIST FIGURE 11 CLUTCH ASSEMBLY MODEL • QTY •• QTY ITEM DESCRIPTION QTY. “DPC-9T” Piston/Drive Disc “DPC-11T” Cylinder/Drive Disc Friction Facing Housing... -
Page 14: Warranties
Exclusive Remedy The exclusive remedy of the Buyer for any breach of the warranties set out above will be, at the sole discretion of Nexen, a repair or replacement with new, serviceably used or reconditioned Product, or issuance of credit in the amount of the purchase price paid to Nexen by the Buyer for the Products.
Need help?
Do you have a question about the AIR CHAMP DPC-9T and is the answer not in the manual?
Questions and answers