Related Manuals for Nexen AIR CHAMP Series
Summary of Contents for Nexen AIR CHAMP Series
- Page 1 ® MEX (55) 53 63 23 31 MTY (81) 83 54 10 18 QRO (442) 1 95 72 60 ventas@industrialmagza.com DIST. AUTORIZADO Reverse Taper Single Flex and Double Flex Couplings FORM NO. L-20264-C-1201...
- Page 2 ® MEX (55) 53 63 23 31 MTY (81) 83 54 10 18 In accordance with Nexen’s established policy of constant product improvement, the specifications contained in this QRO (442) 1 95 72 60 ventas@industrialmagza.com DIST. AUTORIZADO manual are subject to change without notice. Technical data listed in this manual are based on the latest information available at the time of printing and are also subject to change without notice.
-
Page 3: Table Of Contents
® MEX (55) 53 63 23 31 MTY (81) 83 54 10 18 Table of Contents QRO (442) 1 95 72 60 ventas@industrialmagza.com DIST. AUTORIZADO INTRODUCTION ------------------------------------------------------------------------------------------------------------------------------ 1 INSTALLATION --------------------------------------------------------------------------------------------------------------------------------- 1 REPLACEMENT PARTS ------------------------------------------------------------------------------------------------------------------ 4 PARTS LIST -------------------------------------------------------------------------------------------------------------------------------------- 5 WARRANTY ------------------------------------------------------------------------------------------------------------------------------------- 7 (iii) -
Page 4: Introduction
DIST. AUTORIZADO INTRODUCTION Nexen's Single and Double Flex, universally designed couplings combine with Nexen's Open or Enclosed 4H and 5H Series Clutches and Torque Limiters. The Open 5H Series Tooth Clutches have four mounting holes; the Enclosed 4H and 5H Series and Torque Limiters have six mounting holes. - Page 5 (See Table 1). NOTE 12. Alternately and evenly tighten the Hex. Nuts (Item 6) to the For best results, Nexen recommends the use of a dial recommended torque (See Table 1). indicator when checking the limits for parallel and angular misalignment.
- Page 6 NOTE Make sure there are no burrs on the shafts or keys. NOTE For best results, Nexen recommends the use of a dial NOTE indicator when checking the limits for parallel and Do not tighten the set screws provided with the taper angular misalignment.
-
Page 7: Replacement Parts
® MEX (55) 53 63 23 31 MTY (81) 83 54 10 18 Secure the Clutch or Torque Limiter with the Coupling 12. Insert the Disc Pack and Flange Assembly between the QRO (442) 1 95 72 60 ventas@industrialmagza.com DIST. AUTORIZADO Adapter to the shaft according to the instructions provided Coupling Adapter (Item 1) and the Coupling Hub (Item 4) with the Clutch or Torque Limiter. -
Page 8: Parts List
® MEX (55) 53 63 23 31 MTY (81) 83 54 10 18 QRO (442) 1 95 72 60 ventas@industrialmagza.com DIST. AUTORIZADO PARTS LIST SINGLE FLEX COUPLING FIGURE 3 n i l t i n l n i t i n l F ( ) e l n i l... - Page 9 ® MEX (55) 53 63 23 31 MTY (81) 83 54 10 18 DOUBLE FLEX COUPLING QRO (442) 1 95 72 60 ventas@industrialmagza.com DIST. AUTORIZADO FIGURE 4 n i l t i n l n i t i n l F ( ) e l n i l FORM NO.
-
Page 10: Warranty
Buyer shall be obligated to pay or which Buyer may incur based upon, related to or arising out of its contracts with its customers or other third parties. In no event shall Nexen be liable for any amount of damages in excess of amounts paid by Buyer for Products or services as to which a breach of contract has been determined to exist.
Need help?
Do you have a question about the AIR CHAMP Series and is the answer not in the manual?
Questions and answers