Bosch BT-ANGLEEXACT 2 Original Instructions Manual page 27

fore you can switch the tool on again. This prevents you from
accidentally retightening screws that are already firmly in
place.
Adjusting the angled screw head
BT-ANGLE EXACT 2 | 3 | 6 | 7 | 8 | 15 | 17 | 23 | 30
You can adjust the angled screw head (3) to a total of eight
different positions.
Hold the power tool with the open-ended spanner (6)
against the spanner flat (5) of the angled head flange.
Never clamp the power tool to the housing shells.
u
Loosen the cap nut with the open-ended spanner (4) against
the spanner flat (16). Move the angled screw head (3) in 45°
degree increments into the required position and tighten the
cap nut again with the open-ended spanner (4) against the
spanner flat (16).
While doing this, place the open-ended spanner (6) against
the angled head flange to hold it in place.
Adjusting the LED worklight (see figure H)
BT-ANGLE EXACT 2 | 3 | 6 | 7 | 8 | 15 | 17 | 23 | 30
Press the marking ring (19) with a thin screwdriver blade, a
spatula or similar implement. Slide the spring ring(29) back
onto the housing shell using a pair of spring ring pliers.
The two shell halves of the LED holder (15) that encase the
LED worklight (20) can now be brought into the required po-
sition. Taking care not to damage the cable on the LED work-
light, slide the cable into the cavity provided for it (30) in the
housing shell without allowing it to bend. Encase the LED
worklight (20) in the two housing shells of the LED holder
(15) once again.
Press the spring ring (29) and the marking ring (19) back
into their original position.
Maintenance and Service
Maintenance and Cleaning
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Lubricating the power tool
Lubricant:
Special gearbox grease (225 ml)
Article number 3 605 430 009
Molykote grease
Motor oil SAE 10/SAE 20
– Clean the gearbox with a mild solvent after the first 150
operating hours. Follow the solvent manufacturer's in-
structions on use and disposal. Then lubricate the gear-
box with Bosch special gearbox grease. Repeat the clean-
ing process once every 300 operating hours after clean-
ing has been carried out for the first time.
Bosch Power Tools
– After driving 100,000 screws, oil the moving parts of the
shut-off clutch with a couple of drops of SAE 10/SAE 20
motor oil. Lubricate the sliding and rolling parts with Mo-
lykote grease. Use this occasion to check the clutch for
wear to ensure that accuracy and reproducibility have not
been affected. You will need to reset the clutch torque
once you have done this.
Have maintenance and repair work performed exclus-
u
ively by a qualified specialist. This will ensure that the
safety of the power tool is maintained.
An authorised Bosch after-sales service point will handle this
work quickly and reliably.
Dispose of lubricants and cleaning products in an en-
u
vironmentally friendly manner, taking legal regula-
tions into account.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Cambodia
Robert Bosch (Cambodia) Co., Ltd
Unit 8BC, GT Tower, 08th Floor, Street 169,
Czechoslovakia Blvd, Sangkat Veal Vong
Khan 7 Makara, Phnom Penh
VAT TIN: 100 169 511
Tel.: +855 23 900 685
Tel.: +855 23 900 660
www.bosch.com.kh
People's Republic of China
China Mainland
Bosch Power Tool (China) Co. Ltd.
Bosch Service Center
567, Bin Kang Road
Bin Kang District
Hangzhou, Zhejiang Province
China 310052
Tel.: (0571) 8887 5566 / 5588
Fax: (0571) 8887 6688 x 5566# / 5588#
E-Mail: bsc.hz@cn.bosch.com
www.bosch-pt.com.cn
HK and Macau Special Administrative Regions
Robert Bosch Co. Ltd.
21st Floor, 625 King's Road
North Point, Hong Kong
Customer Service Hotline: +852 2101 0235
Fax: +852 2590 9762
E-Mail: info@hk.bosch.com
www.bosch-pt.com.hk
English | 27
1 609 92A 5P3 | (06.04.2020)