Table of Contents
Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
AND OWNER'S MANUAL
Thank you for purchasing an ACCESS Lorado roll-up cover. ACI has manufactured this roll-up cover
with pride using superior quality materials and craftsmanship. With proper care, your cover will
provide years of service and enjoyment.
NOTICE TO INSTALLER: It is recommended you take the time to read these instructions before
installing this cover even if already familiar with the product. Often improvements are made
without prior notice. Always handle cover and components with care to avoid damage. If you find
a part missing or defective, or if you are having trouble installing this product, please have serial
number ready (found on decal under rear bar by tailgate) and call the customer service number on
the back page. When done, these instructions and warranty information must be given to the
consumer.
NOTICE TO CONSUMER: Before using this product, read the operating instructions,
maintenance and safety sections of this owners manual and save for future reference.
Advertisement
Table of Contents
Related Manuals for Access LORADO
Summary of Contents for Access LORADO
- Page 1 INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL Thank you for purchasing an ACCESS Lorado roll-up cover. ACI has manufactured this roll-up cover with pride using superior quality materials and craftsmanship. With proper care, your cover will provide years of service and enjoyment.
-
Page 2: Installation Instructions
INSTALLATION INSTRUCTIONS: (NOTE: For additional installation assistance go online to lorado.com, instruction manual and click on installation video.) PREPARATION Unpack cover components. Clean truck box if dirty. COMPONENTS: 1 driver side rail 1 passenger side rail 1 Element seal kit... - Page 3 1. INSTALLING COVER SIDE RAILS CONT’D. C. Install 2nd clamp on rail at midway point of box. Check if rail is level. If rail tilts up, loosen clamp, lower it and tighten. If rail tilts down, loosen clamp, raise it and tighten. Install 3rd clamp as 2nd clamp close to tailgate as possible.
- Page 4 3. ASSEMBLING TENSION ADJUSTERS TO COVER A. The cover comes pre-rolled to its normal open position for ease of installation. Set pre-rolled cover on “L” Left tailgate with front bar facing up as XT-Dial shown. Align XT-Dial Tension Adjuster (marked L) on driver side of cover - positioned as shown in photo.
- Page 5 4. MOUNTING COVER TO SIDE RAILS CONT’D. C. Hold bolt at top and tighten nut under side rail. Repeat procedure for right hand tension adjuster. center front bar between rails until space is equal at both ends D. Center the front bar between the two side rails.
-
Page 6: Safety Information
5. INITIAL OPERATION AND ADJUSTMENTS A. Unroll cover and place rear bar into strikes on side rails and press down on bar to close (20-30 pounds pressure). B. Close tailgate slowly - top of tailgate should fit snug under cover bar. If it is too tight - raise rails by loosening rear clamps adjust rail up and tighten clamps. - Page 7 AUTO LATCH II OPERATION Pull Loop Down Latch Latch to Unlatch Cover A. TO CLOSE: B. TO OPEN: Engage rear bar into strikes and push down on Open tailgate, near driver side, reach under cover bar until both latches lock into place under rear bar and pull loop down, at same time lift side rails.
-
Page 8: Parts Diagram
PARTS DIAGRAM QUICK RELEASE STORAGE STRAPS SUPPORT FRONT COVER BAR XT-DIAL TENSION ADJUSTER (LEFT) ⅜” x 1-¼” BOLT, WASHER (2 PER COVER) REAR ROLL-UP FRONT ELEMENT SEAL RIGHT SIDE RAIL AUTO LATCH II DUAL LATCHING ⅜” x ¾” BOLT, SYSTEM WASHER, NUT (2 PER COVER) LEFT... -
Page 9: Inspection And Maintenance
INSPECTION AND MAINTENANCE • Inspection and much of the maintenance can be done by the operator. It may be necessary to review the installation and operating instructions. • Periodically inspect the cover assembly and the condition of all parts. Check for loose bolts and parts and tighten if needed.