Sony STR-DN1070 Service Manual page 91

Pin No. Pin Name
AC1 NC
AC2 NC
AC3 DDRVCCIO1
AC4 DGND12_K
AC5 AVDD33_MEMPLL
AC7 DDRVREF_C
AC8 RDQM2
AC9 DGND12_K
AC10 RBA0
AC11 DDRVCCIO1
AC12 RA6
AC14 DDRVCCIO1
AC15 RBA1
AC17,
RDQ10, RDQ15
AC18
AC19 DDRVCCIO1
AC21 NFRBN2
AC24 GPIO27
AC25 DDC_SCL_RX2
AC26 CEC2
AC27 TXVN_1
AC28 TXVP_1
AD1 NC
AD2, AD3 NC
AD4 AVSS33_MEMPLL
AD8 RA13
AD9 RRESET
AD10 RCAS_
AD11 to RA14, RA8, RA1,
AD15 RA10, RA12
AD16 to
RDQ8, RDQ12, RDQ14
AD18
AD19 DDRVCCIO1
AD20 AVDD33_LDO
AD21 NFRBN
AD22 NFCLE
AD23 MDC
AD24 DDC_SDA_RX2
AD25 PWR5V_RX
AD26 HTPLG_RX_2
AD27 REXT
AD28 HTPLG
AE3 NC
AE5 DDRVCCIO1
RDQ29, RDQ31,
AE6 to AE8
RDQ30
AE9 RWE_
AE10 RODT
AE11 RRAS_
AE12 RA3
AE13 RCSX_
AE14 RA4
AE16 RDQ11
AE17 RDQM1
AE18 RDQ13
AE19,
DVCC33_IO_STB
AE20
I/O
- Not used
- Not used
- Power supply terminal (+1.5V)
- Ground terminal
- Power supply terminal (+3.3V)
I Reference voltage (+0.75V) input terminal for SD-RAM
O Data mask signal output to the SD-RAM
- Ground terminal
O Bank address signal output to the SD-RAM
- Power supply terminal (+1.5V)
O Address signal output to the SD-RAM
- Power supply terminal (+1.5V)
O Bank address signal output to the SD-RAM
I/O Two-way data bus with the SD-RAM
- Power supply terminal (+1.5V)
- Not used
O WOL (wake-on-LAN) wake-up signal output to the system controller "H": wake-up
O I2C clock signal output to the HDMI IN 2 connector
- Not used
- Not used
- Not used
- Not used
- Not used
- Ground terminal
O Address signal output to the SD-RAM
O Reset signal output to the SD-RAM "L": reset
O Column address signal output to the SD-RAM
O Address signal output to the SD-RAM
I/O Two-way data bus with the SD-RAM
- Power supply terminal (+1.5V)
- Power supply terminal (+3.3V)
O Ready/busy selection signal output to the NAND fl ash "L": busy, "H": ready
O Command latch enable signal output to the NAND fl ash
- Not used
I/O Two-way I2C data bus with the HDMI IN 2 connector
I Power supply voltage (+5V) input from the HDMI IN 1 connector
O Hot plug detection signal output to the HDMI IN 2 connector
- External reference resistor connection terminal
I Hot plug detection signal input from the HDMI ARC OUT connector
- Not used
- Power supply terminal (+1.5V)
I/O Two-way data bus with the SD-RAM
O Write enable signal output to the SD-RAM
O On die termination enable signal output to the SD-RAM
O Row address signal output to the SD-RAM
O Address signal output to the SD-RAM
- Not used
O Address signal output to the SD-RAM
I/O Two-way data bus with the SD-RAM
O Data mask signal output to the SD-RAM
I/O Two-way data bus with the SD-RAM
- Power supply terminal (+3.3V)
Description
STR-DN1070
91