Download Print this page

Turnigy Decathlon-46 Assemble Manual

Hide thumbs Also See for Decathlon-46:

Advertisement

Quick Links

Wing Span:62.6in/1591mm Flying Weight:1900-2350g
Wing area:41.2sq.dm
Length:43.3in/1100mm
CAUTION : this plane is not a toy!
Before use , please carefully read this manual.
●First-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce its
performance to full extent .
●Assemble this kit only in places out of children's reach!
●Take enough safety percautions prior to operating this model.
You are responsible for this model's assembly and safe operation!
●Always keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
Radio:4channels 5servos
Engine:2cycle40-46;4cycle52

Advertisement

loading
Need help?

Need help?

Do you have a question about the Decathlon-46 and is the answer not in the manual?

Questions and answers

Summary of Contents for Turnigy Decathlon-46

  • Page 1 Wing Span:62.6in/1591mm Flying Weight:1900-2350g Wing area:41.2sq.dm Radio:4channels 5servos Engine:2cycle40-46;4cycle52 Length:43.3in/1100mm CAUTION : this plane is not a toy! Before use , please carefully read this manual. ●First-time builders should seek advice from people having building experience in order to assemble the model correctly and to produce its performance to full extent .
  • Page 2 ELEVATOR AND RUDDER Measure the right position, cut the film from the elevator. Be sure to apply instant type CA glue to both sides of the elevator. Glow the hings to the aileron of the elevator.
  • Page 3 Fixup the elelator servo with TP screw. Link the servo and the tri-horn of the elevator with pushrod.
  • Page 4 Install the rudder as shown and glow it.
  • Page 5: Wheel Installation

    WHEEL INSTALLATION Find out the screw for the wheel as shown. Screw the collar of the wheel. Make sure it is screwed securely. Put the wheel cover in the right position ,then screw it to the landing gear.
  • Page 6: Wing Assembly

    WING ASSEMBLY Cut the hing's holes carefully. Enlarge the holes, to allow the glue to fully infiltration. Insert the hinges into the holes, and glow it to the aileron.
  • Page 7 Be sure to apply instant type CA each hinges. Glue to both sides of each hinges. (low viscosity type) Install the servo into the back of the main wing. Screw the tri-horns to the aileron in the right position.
  • Page 8 Link servo and the tri-horn with the pushrod as shown. The position for the tube to connect the main wings. Before install the main wing, pull the servo lines out of the hole in the fuselage as shown. Link the main wings and the fuselage with the tube.
  • Page 9 Screw the main wing to the fuselage, make sure the safty when flying. Screw the top window with three TP screw.
  • Page 10: Motor Installation

    Motor Installation Seal the ESC as shown. Link the motor and the ESC as shown.
  • Page 11 Install the brushless motor,and fix the ESC with the belt. Fix up the battery and receiver with the belt.
  • Page 12: Engine Installation

    ENGINE INSTALLATION Install the linkage servo and pushrod as shown. Screw the engine support as shown, with the holes predrilled.
  • Page 13 Follow the holes drilled, the angle of the engine should slant right 2°, and down 1.5°. Link the linkage servo and the engine with pushrod as shown.
  • Page 14 COWLING Drill the holes for the engine. Set up the cowling in the right position, and fixup with screw.
  • Page 15 Cover the canopy, pay attention to the magnetic iron. Finished photo...
  • Page 16 Screw each wing support with three TP screws. Start and adjust the engine, after fixup the wing supports.
  • Page 17 CG & Control Throws...