Download
Share
Print this page
Turnigy YAK-54 2C 46 Assemble Manual
  1. Manuals
  2. Brands
  3. Turnigy Manuals
  4. Toy
  5. YAK-54 2C 46
  6. Assemble manual

Turnigy YAK-54 2C 46 Assemble Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Wing Span:52.3in/1330mm;
Wing area:32sq.dm;
Length:45.6in/1160mm;
CAUTION : this plane is not a toy!
Before use , please carefully read this manual.
●First-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce its
performance to full extent .
●Assemble this kit only in places out of children's reach!
●Take enough safety percautions prior to operating this model.
You are responsible for this model's assembly and safe operation!
●Always keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
Flying Weight:2700-2800g;
Radio:4channels 5servos;
Engine:2c 46-50,4c 52-63;
P1

Advertisement

loading
Need help?

Need help?

Do you have a question about the YAK-54 2C 46 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Turnigy YAK-54 2C 46

Summary of Contents for Turnigy YAK-54 2C 46

  • Page 1 Wing Span:52.3in/1330mm; Flying Weight:2700-2800g; Wing area:32sq.dm; Radio:4channels 5servos; Length:45.6in/1160mm; Engine:2c 46-50,4c 52-63; CAUTION : this plane is not a toy! Before use , please carefully read this manual. ●First-time builders should seek advice from people having building experience in order to assemble the model correctly and to produce its performance to full extent .
  • Page 2 Gather the wings,servo cover, aluminium joiner and other parts together. Connect the aileron and the main wing by hinges. Be sure to apply instant type glue to both sides of each hinges. Cut away covering film for the servo.
  • Page 3 Glue the two wood offered as shown. Put the servo into the hole and pull out the servo extension from main wing. Apply instant glue along the edge of servo cover.
  • Page 4 Link the servo and tri-horns with pushrod and straper. 4*15 screw Use one screw to lock the wing to the fuselage on each sides. Insert the servo extention as shown. Gather the stablizers, elevator rudder and other parts together.
  • Page 5 Measure the right position and remove the film from the stabilizer. Connect the elevator and the stabilizer by hinges. Be sure to apply instant type glue to both sides of each hinges. Apply instant type glue to both sides of each hinges of the rudder.
  • Page 6 Screw four TP screws to fix up the tail wheel on the tail of the fuselage. Loop the cable back through the brass swage tube as shown. Crimp the brass tube with a crimping tool or pliers.
  • Page 7 PUSHRODS FUEL TANK...
  • Page 8 Install the throttle servo and the throttle rod as shown. Drill four holes on firework. Gather the four mounts together, then attach them to the firework.
  • Page 9 Install the engine mount on both sides with four screws. Use the ruler to measure the length from firewall to airscrew, which should be 125 MM. Screw the wheel to the landing gear. Be assured that the screw is fixed up.
  • Page 10 Install the wheel cover, and fix it up to landing gear with TP screw. Drill four holes for the landing gear assembly on the fuselage. Attach four mount nuts into the fuselage as shown.
  • Page 11 Istall the canopy bottom as shown. Screw the canopy bottom with four screws. Install the cowling with four TP screws.

  • Page 12: Control Surface Movement

    CONTROL SURFACE MOVEMENT 55mm 55mm 85mm 85mm 30mm 30mm 80-90mm 80-90mm...