Page 1
All manuals and user guides at all-guides.com Wing Span:70.8in/1800mm; Flying Weight:3600-3800g; Wing Area:64sq.dm; Radio:6channels 5-6servos; Length:69in/1755mm; Engine:26-30CC GAS; CAUTION : this plane is not a toy and should be kept away children under 16 years of age! Before use , please carefully read this manual.
All manuals and user guides at all-guides.com MAIN WINGS Connect the aileron and main wing with horns. Cut away covering film for the servo. Pull out the extention from the rib of the main wing.
Page 3
All manuals and user guides at all-guides.com Find out the holes in each sides of fuselage, then remove the covering. Plastic Fixup the wings with plastic bolt bolts on both sides.
All manuals and user guides at all-guides.com MAIN LANDING GEAR Gather the wheels,axles and collars as shown. Carbon Fiber Landing gear Wheel Pants Permanently tighten the axle to the gear strut by wrenches. Install wheel pants with two mounting bolts.
Page 5
All manuals and user guides at all-guides.com Install the main landing gear on the bottom of the fuselage. Pay attention to:we have CB and AL landing gear for choice. and the assembly way is the same. ELEVATOR AND RUDDER Elevator assemblies.
Page 6
All manuals and user guides at all-guides.com Install elevator servos on each sides of tailplane. Elevator pushrod.
Page 7
All manuals and user guides at all-guides.com Rudder assemblies. Tighten the second loop through the brass swage tube. Crimp the brass tube with a crimping tool or pliers.
All manuals and user guides at all-guides.com Rudder pushrod. Push rods Rudder servo arm TAIL WHEEL Bend the tail landing gear to fit for the rudder and insert it into the rudder.
Page 9
All manuals and user guides at all-guides.com Glue the tail wheel wire to the rudder securely. Install the tail wheel, and fasten the presser of the tail wheel to the stabilizer by screws. FUEL TANK...
Page 10
All manuals and user guides at all-guides.com wrap Place the hatch. Use two screws to secure it firmly. Another method for the rudder and elevator servo installation Install the ball linkege connector.Calculate the length proportion between the servo arm and the horn.Rotate the ball linkage connector to an appropriate position.
Page 11
All manuals and user guides at all-guides.com Connect the elevator and stabilizer with horns and U steel wire. Insert elevator to the tailplane with U shape wire. Controled by only 1 elevator servo which is linked.
Page 12
All manuals and user guides at all-guides.com ENGINE Gather the engine and spare parts as shown. The finished picture as shown.
Page 13
All manuals and user guides at all-guides.com Install the DLE 30CC as shown. Pay attention to:you have DLE and MLD for choice.
Page 14
All manuals and user guides at all-guides.com COWLING Mounting the cowling by screws. CG POSITION & CONTROL THROWS 120MM 4.72IN...
Page 15
All manuals and user guides at all-guides.com THE FINISHED PHOTO...
Page 16
All manuals and user guides at all-guides.com...
Page 17
All manuals and user guides at all-guides.com...
Page 18
All manuals and user guides at all-guides.com...
Page 19
All manuals and user guides at all-guides.com...
Page 20
All manuals and user guides at all-guides.com...
Page 21
All manuals and user guides at all-guides.com...
Page 22
All manuals and user guides at all-guides.com...
Page 23
All manuals and user guides at all-guides.com...
Page 24
All manuals and user guides at all-guides.com...
Page 25
All manuals and user guides at all-guides.com...
Page 26
All manuals and user guides at all-guides.com...
Page 27
All manuals and user guides at all-guides.com...
Page 28
All manuals and user guides at all-guides.com...
Need help?
Do you have a question about the YAK-54 26CC and is the answer not in the manual?
Questions and answers