Related Manuals for Arecont Vision Contera AV02CID-100
Summary of Contents for Arecont Vision Contera AV02CID-100
- Page 1 Contera Indoor Dome ® Installation Manual 1080p AV02CID-100 AV05CID-100 +1.818.937.0700 www.arecontvision.com avsales@arecontvision.com...
-
Page 2: Table Of Contents
Table of Contents About Our Warranty ........................... 3 Global (3 Year) Limited Warranty ......................3 Camera Overview ............................4 Package Contents ............................5 Installation ..............................7 Camera Power Up............................9 Alarm I/O Functions ..........................10 Reset to Factory Default ........................... 10 Camera Discovery, Setup, and Configuration ................... -
Page 3: About Our Warranty
About Our Warranty Global (3 Year) Limited Warranty ARECONT VISION warrants to Purchaser (and only Purchaser) (the “Limited Warranty”), that: (a) each Product shall be free from material defects in material and workmanship for a period of thirty-six (36) months from the date of shipment (the “Warranty Period”);... -
Page 4: Camera Overview
Arecont Vision was the first to bring H.264 to the mainstream market and recently developed SNAPstream™ (Smart Noise Adaptation and Processing) technology for reducing bandwidth without impacting image quality. -
Page 5: Package Contents
CAUTION! Do not attempt to service a damaged unit yourself. Refer all servicing to qualified service personnel. Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application. - Page 6 Cables • Contera Indoor Dome | Installation Manual...
-
Page 7: Installation
Installation Description Supplied Dry Wall Anchors Supplied Screws Contera Indoor Dome Camera Supplied Set Screw Camera Dome Cover 1. Determine a secure location to mount the camera 2. Use the template, anchors, and screws provided to prepare the mounting provisions for the camera installation. - Page 8 10. To adjust the zoom and focus, see the “Zoom and Focus” Section of this manual. 11. Install the camera dome cover back once you finish all the above steps. Please make sure you align the marks on the camera and the dome cover. 12.
-
Page 9: Camera Power Up
Camera Power Up CAUTION! This product should be installed by a qualified service technician in accordance with the National Electrical Code (NEC 800 CEC Section 60) or applicable local code. Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application. -
Page 10: Alarm I/O Functions
Alarm I/O Functions Connect the Alarm In (DI) connector to the alarm input sensor, and connect Alarm Out (DO) connector to the alarm output signal. To avoid any damaged, please follow the specification of the part as below: Alarm In (Dry Contact) Alarm Out (Dry Contact) V sense V sense... -
Page 11: Camera Discovery, Setup, And Configuration
The AV IP Utility tool is compatible with all Contera ® cameras. The user manual for the software is available at Arecont Vision website: http://www.arecontvision.com/softwares.php Camera Discovery 1. Locate and double click the AV IP Utility shortcut on the desktop. -
Page 12: Web Interface Navigation
Web Interface Navigation The entire menu categories are located on the top of the web interface, and clicking on any one of the buttons will cause left side of the page to jump to the settings section for the selected button. The following are the camera settings available on the top of the web interface: The following are the camera settings available on the top of the web interface: Image... - Page 13 • Firmware Upgrade • Reboot & Restore Settings Date/Time • • Administration Administrator settings • • Viewer Management About • • Support Contera Indoor Dome | Installation Manual...
-
Page 14: Zoom And Focus
Zoom and Focus Menu Feature Description Manual Zoom/ Focus: Numbers indicate the level of Zooming/ focusing in order to adjust the field-of-view. +20, +5, +1, -20, -5, -1 Enable Auto Focus Zoom Camera will do Auto Focus after changing zoom lens group position. -
Page 15: Image
Image Menu Feature Description Controls the overall brightness of the camera image Brightness and works in conjunction with the exposure controls to maintain the image brightness. Controls sharpness and edge definition of the image. Setting this to lower levels may make overall image Sharpness appear a bit softer while causing lines and edges in the image to look smoother. - Page 16 Menu Feature Description Auto detects bright backlight, glare or high contrast lighting and automatically selects the WDR level. Auto Note: WDR enabled will decrease the FPS of 5MP camera. Manually adjusts the intensity of backlight compensation. Note: WDR enabled will decrease the FPS of 5MP camera.
- Page 17 Moonlight Mode Moonlight Mode: Limits exposure time from 20ms to 500ms. This mode produces the best image quality Custom Exposure Mode under very low light conditions with the least amount of image noise. The trade-off is in favor of low noise at the expense of high motion blur.
- Page 18 Camera Name Specifies a name for the camera. The maximum length is 32 characters. Background Configures the background color of the text overlay. The options are Translucent (light grey) or Transparent. Translucent Transparent Text Color Options are Black, White, Green, or Yellow. Text Overlay There are four content positions (Top Left, Top Right,...
-
Page 19: Video
Video Menu Feature Description Disable Video: Disables live video on the screen. MJPEG over HTTP: This radio button is the default browser display option. No plug in is required as most Show Video Type: browsers can decode MJPEG images. Disable Video MJPEG over HTTP H.264 over RTP/UDP: Displays video using H.264. - Page 20 Controls the image size and image cropping features. Resolution: Left, Top, Right, and Bottom numeric fields set custom Left image size cropping and crop area coordinates in Right pixels. Supported values are 0 to maximum resolution Bottom in pixels (maximum varies based on the sensor resolution being cropped) Video Compression: Radio buttons to select the desired compression.
- Page 21 H.264 image quality setting for variable bit rate control. Setting a lower value results in higher image quality, higher value results in lower image quality. H.264 Quality Frame rate adjustment for the camera video stream. Note: For 5MP models, FPS will be up to 50% of specified FPS if WDR is enabled.
-
Page 22: Network
Network Menu Feature Description DHCP: If checked, the camera will attempt to obtain its IP address from the DHCP server available on the network. IP Assignment: IP Address: Sets the current IP address of the camera. DHCP Subnet Mask: Once set, the camera will use these IP Address mask bits to determine if a destination is from a Subnet Mask... - Page 23 Enable QoS Enables quality of service. Video QoS Sets DSCP value for video traffic. Management DSCP Sets DSCP value for non-video traffic. Enable UPnP Enables Universal Plug and Play function. Port Configures the port number for stream 1 to stream 3. The range is 554/1025~65535.
- Page 24 Audio IP Configures the multicast address and the port number to stream audio. Audio Port *This function is supported depends on models. Meta IP Configures the multicast address and the port number to the HTML meta. Meta Port Path Configures the URL address of the video stream. Configures the time-to-live threshold of the multicast datagram before it is discarded by the router.
- Page 25 Community String Specifies the name of the community to access to SNMP information. Trap Configuration: Specifies the destination IP address to send SNMP trap messages. Address Community String SNMP v3 Enables SNMP version 3 support. SNMP User Specifies the user name of the SNMP v3. Authentication Selects one of the Authentication modes from the dropdown menu.
- Page 26 Enable Enables FTP access to the camera. Note: This function is only available when a SD card is installed. You can access files in the SD card via FTP. Password Specifies and confirms the password to access the Confirm FTP. Max.
-
Page 27: Privacy Mask
Privacy Mask Menu Feature Description Enable Privacy Mask Creates a privacy mask on the image so the selected areas will not be visible. Contera Indoor Dome | Installation Manual... -
Page 28: Event
Event Menu Feature Description Enable Turns on and off on-camera motion detection Extend Enables the extended motion detection and motion detection zones increase from default 64 to 1024 for enhanced motion detection sensitivity. Zone Size Adjusts the size of motion detection zones. Detail Sets the size of each zone displayed by the motion detection grid contains sub zones the number of which... - Page 29 Alarm Schedule Configures the alarm schedule by holding down the mouse button and clicking the time block to enable the schedule settings on the selected time. A light blue color on the time block indicates that the alarm schedule is enabled, while a light grey color indicates that the alarm schedule is disabled.
- Page 30 Sensitivity Configures the sensitivity level of Tampering Detection: High, Medium, and Low. Host Address: Specifies the host name or IP address Remote Server of the FTP server. Host Address Port: Specifies the port number of the FTP server. Port Username: Specifies the login username of the FTP Username server.
- Page 31 Login Certificate Specifies the login Username Password for the network storage sever. Recipient Setup Network Storage Status: Displays the current status of the connection with the network storage server. Network Storage Status not_mounted or ok) Network Address Network Address: Specifies the IP address of the network storage server.
- Page 32 SD Card Information Available Storage: Displays the available storage of the SD card if it is installed. Format SD Card: Erases all the data stored on the SD Card. Available Storage Format SD Card Usage: Displays the total storage that has been used now.
-
Page 33: System Options
Records all the status information of the camera in list format. Downloads the log file to the computer as a text file. Note: The log file is protected by a password. Please contact with Arecont Vision technical support team. Reboot & Restore Settings Reboot the Camera: Reboots the camera. -
Page 34: Administration
Note: If admin password was set but has been lost, it can be erased by AV IP Utility using the key file. Please contact Arecont Vision technical support to obtain the key file required to perform this function. Or, if the camera has a reset button, you can also reset to Factory default for removing the password. - Page 35 Viewer Management User List: Displays current user accounts created on the camera. Clicks New User/ Delete User to create or User List remove a user account. User Name Viewer Password User Name: Specifies the user name. It must be at Confirmation least five and up to sixteen characters.
-
Page 36: About
About Menu Feature Description About Displays the information of the camera: Model Name, Firmware, Serial Number, and MAC Address. Support Menu Feature Description Support Provides several useful hyperlinks for users who would like to get more information of the camera. Contera Indoor Dome | Installation Manual... -
Page 37: Mounting Template
Mounting Template Contera Indoor Dome | Installation Manual... - Page 38 Arecont Vision. The information in this publication is believed to be accurate in all respects. However, Arecont Vision cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice.