Table of Contents
Advertisement
9901930
9900800
9900032
9901928
7656056 (without stone,
screw or washer)
7658200 (Coarse - 80K)
7658300 (Medium - 120K)
9901280
Y
"",~9900338
~4548593
1270100 (Medium -120K)
1270200 (Coarse -80K)
9902400
7664195
9901930
9900800
7664194
7672000
7654200
"'--?r---
7654000
1221900
-----li~
7648050
- - ( I " I ~ 1
(
rt:=: : : :
167m'
1222193
~
~"
9900117
e
1 274000
7650 100
----+=~
1286193
--*!~-"
1286000
1286200
7654059
Series
Grinding
Head
Complete
SERIES X
SHARPENER
Grinding Head only, See page
26 for Sharpener Housing,
Reverse Drive, Sharpener Tube
and related parts.
~
76820005"-8"
~(127mm-203mm)
o
7682100
~
10" (254mm)
~
~9900307
1265000
Millimeter Equivalents
Machine Strokes:
1-1/8" Ex.
short, 29mm;
1-1/4"
Short, 32mm;
1-3/8"
Med., 35mm;
1-1/2"
Long,
38mm;1-3/4" Ex.
long, 44mm.
Machine Sizes: 5" - 127mm; 6" - 152mm;
7"
178mm; 8" - 203mm; 10"- 254mm; 14"- 365mm.
SERIES X Sharpener Installation Instructions
If your PACER is supplied with the option SERIES 'X' style grinder
head, this page gives you the necessary parts listings.
If you desire to change over a regular WOLF Pacer VI to a Pacer
SERIES 'X' ... in other words use the Series 'X' grinder head as
opposed to the regular Pacer style. You must order six (6) parts as
follows: One 7654059 - Grinder Head Complete; One 1274000
Presserfoot Rod Bushing Complete; One 10"-7682100 or 8"
7682000 Wear Plate (specify size); 1305060 Follower Guide Assy
(not shown); 1305500 Guide and (2) 9900312 Screws.
To install the Series X grinder head on a Pacer it is necessary to
drill the bottom of the sharpener housing (1200000) to accommo
date the wear plate. It is also necessary to install the new part spac
er on to the pressertoot rod just above the pressertoot to prevent the
grinding wheels from rubbing on the pressertoot.
Part No.
Description
Quantity used
if more than 1
Part No.
Description
Quantity used
if more than 1
1212200
1221900
1222193
1246000
1247000
Hex Nut - Thin
Bearing
Retaining Ring
Idler Gear
Idler Gear Shaft
7664194
7664195
7664500
7666193
7672000
Grinding Wheel Arm - SA - L.H.
Grinding Wheel Arm - SA - R.H.
Adjusting Spring
Bronze Bushing
Stud 2
2
2
32
1251000
1265000
1266493
1270100
1270200
1274000
1286000
1286193
1286200
4548593
7648050
7650100
7654000
7654200
7656000
7656056
7657000
7658200
7658300
Bushing (for Pressertoot Rod)
Drive Belt
Retaining Ring
1" (25.4mm) Emery Wheel (Medium - 120 K)
1" (25.4mm) Emery WHeel (Coarse - 80K)
Pressertoot Bushing
Idler Pulley
Bearing
Spacer - Idler Pulley
Emery Wheel Washer
Gear Shaft Assembly
Drive Pulley
Housing - Grinding Head
Stop Bracket
Grinding Wheel Shaft
Shaft
&
Pulley SA
2
Pulley
1-3/8" (34.9mm) Emery Wheel (Coarse-80K)
1-3/8" (34.9mm) Emery Wheel (Medium-120K)
7673095
7673195
7674094
7674194
7682000
7682100
7693000
9900032
9900117
9900121
9900307
9900338
9900800
9901280
9901845
9901928
9901930
9901932
9902400
Support Spring - Inner - R.H.
Outer Pressure Spring - R.H.
Support Spring - L.H. - Inner
Outer Pressure Spring - L.H.
Wear Plate 5" - 8" (127mm - 203mm)
Wear Plate 10" (254mm)
Gasket (Not shown)
Screw
Screw
Screw
Flat Head Screw
Flat Head Screw
Pan Head Screw
Socket Head Cap Screw
Socket HEad Set Screw
Lock Washer
Lock Washer
Lock Washer
Heli-Coil Insert
2
2
2
2
2
4
2
2
Advertisement
Table of Contents
