Table of Contents
Advertisement
1389000
1004600 2 Speed (Square part)
I ' "
1007600 Super, Jr. & Jeans Machine'
1004800 2 Speed (Square part)
(]
SINGLE PHASE
or
THREE PHASE
o
3003400
~ ~
1093200
1371500
1371100
1371600
1371000
1371300
1007450 Single Speed 60 Cycle
1005260 Two Speed
1007250 Super, Jr. & Jeans Machine
k
MOTOR AND CORD CONNECTOR NUMBERS - IN NUMERICAL ORDER
Part No.
Description
Quantity used
Part No.
Description
Quantity used
if more than 1
if more than 1
1004600
Inner Breaker, 2 Speed - 1 Phase (Square part)
1105201
220/1 Phase Twist-Lock Male Plug
1004800
Insulator - 2 Speed - 1 Phase (Square part)
1105300
220/1 Phase Twist-Lock Female Plug
1005260
Outer Breaker - 2 Speed - 1 Phase
1105401
3 Phase Hubbell Male Plug
1007000
3 Phase Spacer
1105500
3 Phase Hubbell Female Plug
1007250
Inner Breaker - Super, Jr. & Jeans Machine -1 Phase
1134060
Ground Wire
1007450
Outer Breaker 60 Cycle - Single Speed - 1 Phase
1371000
Knob
1007550
Outer Breaker 50 Cycle - Single Speed - 1 Phase
1371100
Clip
1007600
Insulator - Super, Jr. & Jeans Machine - 1 Phase
1371300
Spring
1015000
Fan Locknut
1371600
Rear Cover
1024000
Rear Head
1389000
Fan
1048100
Twist-Lock Connector Base - 1 Phase & 3 Phase
3003400
Acorn Nut (8 on Dual & Jeans Machine)
4
1058093
Rear Head Bearing
9900098
Screw for 1 Phase Plug
3
1093200
Bearing Spacer
9900099
Screw for 3 Phase Plug
2
1101950
1 Phase Connection
9900119
Screw for Breaker
2
1102100
1 Phase Brass Insert
9900123
Screw for Rear Cover
4
1105001
110/1 Phase Twist-Lock Male Plug
9900142
Screw for Hubbell Base
3
1105100
110/1 Phase Twist-Lock Female Plug
9901973
Washer
3
21
Installation - Twist-Lock Type Electrical Connector
1105100 (110/1 Phase)
1105300 (220/1 Phase)
1105500 (3 Phase)
9900098 (1 Phase)
9900099 (3 Phase)
1105001 (110/1 Phase)
1105201 (220/1 Phase)
1105401 (3 Phase)
9900142
1048100
(1 Phase & 3 Phase)
1~1134060
(Ground)
(See notes #3
& #4)
,---'--Ground
.-H-I~9901973
1. Discount electrical connector.
2. Remove old type connection box. Pull out
terminal block by removing the 3 screws
on the outside of connection box.
Disconnect wires on the back of the block.
3. If the new male plug is mounted on the
Twist-Lock base, remove it. Bring lead
wires through new base being installed.
Before base is secured to motor case, the
Green Ground wire #1134060 must be
properly attached. Note: Place ground
between base and motor case, attaching
it with anyone of the screws, leading the
other end up through the base.
4. Connect leads and ground wires to male
plug. Make certain ground wire is con
nected to right angle shaped terminal pin.
Note: Be sure three phase machines
rotate in same direction as arrow stamped
on the rear motor case. To check, make a
flash contact with switch turned on. If
rotation is incorrect, reverse by changing
the lead wires on the male plug. Motor
must rotate in proper direction or serve
damage will result.
Cord Connector
1102100
1101950
(1
Phase)
I
1007550 Single Speed 50 Cycle
Advertisement
Table of Contents
