Trotec BE40 Operating Manual
Clamp meter
Hide thumbs
Also See for BE40:
- Operating manual (172 pages) ,
- Operating manual (11 pages) ,
- Original instructions manual (14 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Trotec BE40
Summary of Contents for Trotec BE40
- Page 1 BE40 OPERATING MANUAL CLAMP METER...
-
Page 2: Table Of Contents
Follow the manual condition. Information marked with this symbol indicates that the • Do not open the device. operating manual must be observed. • Observe the storage and operating conditions as given in the Technical data chapter. clamp meter BE40... - Page 3 To use the device for its intended use, only use accessories and Warning spare parts which have been approved by Trotec. The device is not a toy and does not belong in the hands of children. Improper use...
-
Page 4: Information About The Device
Rotary switch Designation Measuring alternating current of up to 1000 A Measuring alternating current of up to 200 A Measuring alternating current of up to 20 A Diode test / continuity test Measuring resistance Measuring DC voltage Measuring AC voltage OFF (for switching the device off) clamp meter BE40... - Page 5 Automatic switch-off after approx. 15 minutes DC measurement Dimensions 229 x 48 x 80 mm (length x width x height) Automatic measuring range selection Weight approx. 303 g Diode test Continuity test MAX indication (indication of the maximum value) HOLD indication (display of the measured value is frozen) clamp meter BE40...
-
Page 6: Transport And Storage
± (1.0 % + 4 digits) 2 kΩ 0 Ω to 2000 Ω 1 Ω ± (1.5 % + 2 digits) 20 kΩ 0 kΩ to 20.00 kΩ 10 Ω ± (1.5 % + 2 digits) 200 kΩ 0 kΩ to 200.0 kΩ 100 Ω ± (1.5 % + 2 digits) 2 MΩ 0 MΩ to 2.000 MΩ 1 kΩ ± (2.0 % + 3 digits) 20 MΩ 0 MΩ to 20.00 MΩ 10 kΩ ± (3.0 % + 5 digits) clamp meter BE40... -
Page 7: Operation
This physical and unavoidable effect can falsify the measurement. In this case, the display shows either no measured values or they are incorrect. Wait a few minutes until the device has become adjusted to the changed conditions before carrying out a measurement. clamp meter BE40... - Page 8 Example: Info If the minus sign (29) appears in front of the measured value, you have confused the measuring object's plus pole with the minus pole. Check the connection and connect the measuring cables with correct polarity. Example: clamp meter BE40...
- Page 9 Make sure that the power of the electric circuit is switched off and all capacitors are completely discharged. • When holding onto the measuring cables, make sure not to reach behind the protection against contact (12). clamp meter BE40...
- Page 10 ð The voltage unit (25) is displayed. ð If OL is indicated on the display, the test probes are not positioned correctly. Info Only measure one conductor at a time to ensure an unambiguous measurement result. clamp meter BE40...
- Page 11 2. Press the HOLD button (4). ð An acoustic signal is emitted. ð The current measured value is frozen in the measurement value display (28). ð The HOLD indication (36) appears on the display. 3. Press the HOLD button (4) again to deactivate the HOLD function. clamp meter BE40...
-
Page 12: Maintenance And Repair
European Parliament and of the Council of 6 September 2006 on batteries and accumulators. Please dispose of batteries and • The opening of the current clamp is dirty. Clean the device accumulators according to the relevant legal requirements. as described in the Cleaning chapter. clamp meter BE40... - Page 13 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...