Advertisement
© 2013 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. ("Avenview") products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and claims any
express or implied warranty, relating to its products are is strictly prohibited.
Control Your Video
Control Commands
VIDEO WALLS
VIDEO PROCESSORS
VIDEO MATRIX SWITCHES
EXTENDERS
SPLITTERS
CABLES & ACCESSORIES
Model #: SW-HBT-C6IRLT-8X8E
WIRELESS
Rev.3.15
Advertisement
Table of Contents
Related Manuals for Avenview SW-HBT-C6IRLT-8X8E
Summary of Contents for Avenview SW-HBT-C6IRLT-8X8E
- Page 1 No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and claims any express or implied warranty, relating to its products are is strictly prohibited.
- Page 2 SERIAL PORT SETTING - Baud Rate: 19200 bps - Data Bit: 8 bits - Parity: None - Flow Control: None - Stop Bit: 1 RS-232 Wiring (Cross Cable Connection) SW-HBT-C6IRLT-8X8E Remote Controller(PC) Assignment De finition è ç www.avenview.com Page 1...
- Page 3 Switch all the Output to 1~8 I1~I8 Display the current matrix status and F/W version System Reset to A1, B2, C3, D4, E5, F6, G7, H8 Setting EDID MODE. 1-STD 2-TV Display all the available commands Quit Exit(for telnet only) www.avenview.com Page 2...
- Page 4 To access the telnet control in Windows 7, click on the 'Start' menu and type "cmd" in the Search field then press enter. Under Windows XP go to the 'Start' menu and click on "Run", type "cmd" with then press enter. Under Mac OS X, go to Go→Applications→Utilities→Terminal See below for reference. www.avenview.com Page 4...
- Page 5 (For a full list of commands, see Section 1.3). Commands will not be executed unless followed by a carriage return. Commands are case-insensitive. If the IP is Note: changed then the IP Address required for Telnet access will also change accordingly. www.avenview.com Page 5...
- Page 6 On a PC/Laptop that is connected to the same active network as the Matrix, open a web browser and type device's IP address on the web address entry bar. The browser will display the device's status, control and User setting pages. Click on the 'Control' tab to control power, input/output ports, EDID and reset mode www.avenview.com Page 6...
- Page 7 Clicking on the 'User Setting' tab allows you to reset the IP configuration. The system will ask for a reboot of the device every time any of the settings are changed. The IP address needed to access the Web GUI control will also need to be changed accordingly on the web address entry bar. www.avenview.com Page 7...
- Page 8 Disclaimer While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein.
Need help?
Do you have a question about the SW-HBT-C6IRLT-8X8E and is the answer not in the manual?
Questions and answers