Download
Share
Print this page
  1. Manuals
  2. Brands
  3. SI Manuals
  4. Indoor Furnishing
  5. Nano Roll
  6. Installation instructions manual

SI Nano Roll Installation Instructions Manual

24v dc - 485
Hide thumbs Also See for Nano Roll:

Advertisement

Quick Links

Download this manual
Nano Roll
Installation Instructions
24v DC - 485
INSTALLERS: Please leave this manual with the owner.
Doc. # 400030

Advertisement

loading
Need help?

Need help?

Do you have a question about the Nano Roll and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for SI Nano Roll

Summary of Contents for SI Nano Roll

  • Page 1 Nano Roll Installation Instructions 24v DC - 485 INSTALLERS: Please leave this manual with the owner. Doc. # 400030...

  • Page 2: Terminal Blocks

    PARTS LIST - NANO ROLL - 24v DC - 485 Shades Terminal Blocks 275 Roll 375 Roll 475 Roll Please note all the Node IDs on your Shade motors. See the last page on these instructions. Wall Brackets (275) + End Caps...
  • Page 3 PARTS LIST - NANO ROLL - 24v DC - 485 Spacer Blocks (optional) Leveling Shims (optional) Pg 2 Parts list - Nano Roll - 24v DC - 485...

  • Page 4: Additional Accessories

    Included with 375 / 475 series only 1/4” Magnetic Driver Included with 275 series only Note: For more information about these tools and their use, please call Tech Support at 512.832.6939 Opt. 1 Pg 3 Additional Accessories list - Nano Roll - 24v DC - 485...
  • Page 5 SPACER BLOCKS AND LEVELING SHIMS (OPTIONAL) Spacer Blocks - used to clear an obstruction in the fabric path. Connect spacer blocks to shade brackets before installation. Note: Do not use more than 4 spacer blocks per bracket. Leveling Shims - used if the window frame is out of level. Connect to shade brackets before installation Note: Do not use more than 2 leveling shims per bracket.
  • Page 6 Data - Data ground 2. Install wall bracket/end cap assembly with the supplied screws for Ceiling Mount for Wall Mount Idler Motor side side Use 1/4” magnetic driver (incl.) Pg 5 Installation - Nano Roll - 24v DC - 485 (275)
  • Page 7 3. Measure bracket to bracket width and verify it matches the ordered width. Adjust accordingly. Brackets must be level before the shade is installed! 4. Remove idler end cap with flat screw driver Pg 6 Installation - Nano Roll - 24v DC - 485 (275)
  • Page 8 6. Insert motor side completely. Then, while supporting motor side, put idler end cap over the idler and snap into place. When installing, the shade should be at the upper limit. Pg 7 Installation - Nano Roll - 24v DC - 485 (275)
  • Page 9 INSTALLATION - 24v DC - 485 (275 SERIES) There will be an audible click. Pg 8 Installation - Nano Roll - 24v DC - 485 (275)
  • Page 10 - 24 VDC Data + Data For 485 Only Data - Data ground 2. If mounting to a wall, remove the ceiling flange from motor and idler brackets Pg 9 Installation - Nano Roll - 24VDC - 485 (375 / 475)
  • Page 11 Use 5/16” magnetic driver (incl.) 4. Measure bracket to bracket width and verify it matches the ordered width. Adjust accordingly. Brackets must be level before the shade is installed! Pg 10 Installation - Nano Roll - 24VDC - 485 (375 / 475)
  • Page 12 INSTALLATION - 24v DC - 485 (375 / 475 SERIES) 5. Remove both end caps 1/16” hex tool Motor End cap Idler End cap Pg 11 Installation - Nano Roll - 24VDC - 485 (375 / 475)
  • Page 13 INSTALLATION - 24v DC - 485 (375 / 475 SERIES) 6. Connect shade and pre-wire, snap connector into spring clip. 7. Align and insert the motor side. Pg 12 Installation - Nano Roll - 24VDC - 485 (375 / 475)
  • Page 14 INSTALLATION - 24v DC - 485 (375 / 475 SERIES) 8. Make sure the motor head bracket is fully seated. Secure with cotter pin. Pg 13 Installation - Nano Roll - 24VDC - 485 (375 / 475)
  • Page 15 INSTALLATION - 24v DC - 485 (375 / 475 SERIES) 9. Put idler end cap over idler and snap into place. There will be an audible click. Pg 14 Installation - Nano Roll - 24VDC - 485 (375 / 475)
  • Page 16 INSTALLATION - 24v DC - 485 (375 / 475 SERIES) 10. Replace and fasten motor end cap 1/16” Hex tool Pg 15 Installation - Nano Roll - 24VDC - 485 (375 / 475)
  • Page 17 PROGRAMMING 485 RS485 shades are programmed using the Screen Innovations SIFI via the web interface. This programming can be done with a Windows or Mac computer either over LAN or wired directly to SIFI. The following instructions are for a Windows computer, but the steps for programming on a Mac are very similar.

  • Page 18: Troubleshooting

    TROUBLESHOOTING TROUBLESHOOTING Tech Support: 512.832.6939 Problem Possible Cause Action to Take Ensure that 24v hardwired motors have at least Shade won’t Motor is not powered. 20VDC and that the polarity is correct. operate. Check the wire pinouts and termination. Look for Incorrect or poor cable broken, loose, or damaged wires.
  • Page 19 NODE IDS Please keep a note of all the Node IDs on your shade motors. OR for larger shade orders, refer to your Sales Order document for the list. Room Shade 1 Shade 2 Shade 3 Shade 4 Shade 5 Shade 6 Room Shade 1...
  • Page 20 Screen Innovations 9715-B Burnet Rd, Suite 400 Austin, TX 78758 512.832.6939 www.screeninnovations.com 400030 v. 1.3 12 November 2019...