SI Nano Roll Manual Operation Instructions
Hide thumbs
Also See for Nano Roll:
- Installation instructions manual (20 pages) ,
- Installation instructions manual (20 pages) ,
- Installation instructions manual (20 pages)
Subscribe to Our Youtube Channel
Related Manuals for SI Nano Roll
Summary of Contents for SI Nano Roll
- Page 1 ® Screen Innovations 9715-B Burnet Rd, Suite 400 Austin, TX 78758 512.832.6939 www.screeninnovations.com 400033 v. 1.3 25 April 2022...
- Page 2 Nano Roll Manual Operation Instructions INSTALLERS: Please leave this manual with the owner.
- Page 3 PARTS LIST – Nano Roll – Manual Operation Shade Wall Brackets 275 Roll End Caps Screws included (3 per bracket) Pg 1 Parts list - Nano Roll - Manual...
- Page 4 ADDITIONAL ACCESSORIES LIST – Nano Roll – Manual Spanner Wrench Set Screw Hex Tool Pre-Tension Tool Note: For more information about these tools and their use, please call Tech Support at 512.832.6939 Opt. 1 Pg 2 Additional Accessories list - Nano Roll - Manual...
- Page 5 Before installing the shades, verify whether the shade was ordered as standard roll or reverse roll. The illustrations in this manual show standard roll shades, but the installation procedure for reverse roll shades is very similar. Idler side Spring side Pg 3 Shade Orientation - Nano Roll - Standard Roll...
- Page 6 SHADE ORIENTATION - Reverse Roll Spring side Idler side Pg 4 Shade Orientation - Nano Roll - Reverse Roll...
- Page 7 1. Insert the pre-tension tool into the spring control, and rotate counter-clockwise until the correct number of pre-tension rotations are set. NOTE: Start with arrows and small rib facing up. NOTE: For reverse roll shades, the tension direction will be opposite. Pg 5 Pre - Tension - Nano Roll - Manual...
- Page 8 PRE-TENSION – Nano Roll – Manual Operation 2. Turn the spring control an extra 1/4 turn and slowly release it to lock the shade spring in place. 1/4 Turn Pg 6 Pre - Tension - Nano Roll - Manual...
- Page 9 INSTALLATION – Nano Roll – Manual Operation NOTE: Nano manual shade brackets are intended to be wall mounted. They may be ceiling mounted, but the appearance is degraded. 1. Hold the wall bracket/end cap assembly against the wall and mark the hole locations.
- Page 10 INSTALLATION – Nano Roll – Manual Operation 4. Insert the idler side, making sure the four small pins are engaged with the bracket. NOTE: Shade should be oriented with weight bar approximately at upper limit. 5. Install the spring side with the small rib and arrows facing upwards.
- Page 11 VERIFY – Spring Tension and Upper Limit 1. Pull the shade down approximately halfway. 2. Pull the shade down a small amount (~1/2”) and release. The shade will run to the upper limit. Pg 9 Verify Spring Tension and Upper Limit...
- Page 12 VERIFY – Spring Tension and Upper Limit 3. If the shade moves too slowly, remove from bracket and add one pre-tension turn at a time until the desired speed is achieved. 4. If the shade moves too quickly, remove from bracket and reduce one pre-tension turn at a time until the desired speed is achieved.
- Page 13 VERIFY – Spring Tension and Upper Limit 5. Adjust the shade limiter using the included spanner wrench as shown below. a. Turn the shade limiter counter-clockwise to b. Turn the shade limiter clockwise to raise lower the upper limit. the upper limit. 6.
-
Page 14: Troubleshooting
TROUBLESHOOTING Tech Support: 512.832.6939 Problem Cause Solution Shade is slow or jerky Spring does not have Add one pretension turn at a time until the shade when moving up enough pre-tension turns operates smoothly. Shade abruptly stops Spring has too many Remove one pre-tension turn at a time until shade at upper limit pre-tension turns... - Page 15 NOTES: Pg 13 Notes...
- Page 16 NOTES: Pg 14 Notes...
Need help?
Do you have a question about the Nano Roll and is the answer not in the manual?
Questions and answers