Scope Of Delivery | Sct 141X | 19; Sct 1410 Aligning Equipment; Sct 1415 S1 Aligning Equipment; Sct 1415 S2 Aligning Equipment - Bosch SCT 141 Series Initial Operation Instruction

3. Scope of delivery
3.1 SCT 141x
Designation
Precision measuring bar
Mount 1 for precision measuring bar
Mount 2 for precision measuring bar
Position indicator
End stop parts set (4x)
Mount for large calibration boards
Star knob screw parts set
Protective hood
Protective hood attachment parts set
(2x)
Ruler
Wall mount
Warning label
Indicator label
SCT 141x operating instructions
P-Assist S5 laser module
1
P-Assist S5 operating instructions
SCT 1410 aligning equipment
SCT 1415 S1 aligning equipment
SCT 1415 S2 aligning equipment
SCT 410 post
3
Tab. 1: Scope of delivery SCT 141x
1 Only included in the scope of delivery of the SCT 1415 S1 and
SCT 1415 S2
2 Only included in the scope of delivery of the SCT 1415 S1
3 Only included in the scope of delivery of the SCT 1415 S2
* Optional accessory
3.1.1 SCT 1410 aligning equipment
Designation
Tape measure mount
Tape measure
3.1.2 SCT 1415 S1 aligning equipment
Designation
Tape measure mount
Tape measure
Chalk line
Plumb bob
3.1.3 SCT 1415 S2 aligning equipment
Designation
Tape measure mount
Tape measure
Chalk line
Plumb bob
Tape measure mount for SCT 410
Robert Bosch GmbH
Part number
1 690 381 118
1 690 381 226
1 690 381 213
1 690 381 214
1 690 381 225
1 690 381 220
1 690 381 230
1 690 382 389
1 690 381 232
1 690 382 469
1 690 381 249
1 690 382 470
1 690 382 482
1 690 386 063
1 690 381 124
1 690 386 038
1
1 690 381 248
1 690 381 246
2
1 690 381 245
3
1 690 381 240
Part number
1 690 381 212
1 693 740 681
Part number
1 690 381 212
1 693 740 681
1 693 740 684
1 693 740 685
Part number
1 690 381 212
1 693 740 681
1 693 740 684
1 693 740 685
1 690 381 206

Scope of delivery | SCT 141x | 19

3.2

SCT 410

Designation
Base plate with assembly material
Post
Angle mounting bracket
Clamp
Mount for large calibration boards
Setting aid*
Operating instructions SCT 410
Tab. 2: Scope of delivery
* Optional accessory
4.

SCT 141x assembly

4.1

Applying safety labels

¶
Attach the safety label to the upper left of the back
of the VW calibration board at a distance of at least
60 mm from the upper frame.
i
If the distance of the label from the upper frame
is less than 60 mm, it will be covered up by the
protective hood that has to be attached to the
DAS 800/1000 (VAS 6430) when using the SCT 141x.
1
3
2
Abb. 1: Attaching the "Warning information" label to a VW calib-
ration board
1 Upper frame
2 Label
3 Distance between upper frame and label: min. 60 mm
en
Part number
1 690 381 155
1 690 381 125
1 690 381 229
1 690 381 233
1 690 381 157
1 690 381 210
1 690 386 066
|
1 690 386 065 2017-09-29