Advertisement
Quick Links
Note:
Lifting the machine in an awkward position or
transporting it in a poorly balanced position could
result in personal injury. When transporting the
machine, assign an adequate number of persons
to the job and ensure that each person can take a
good position of not being excessively loaded.
(mass: approx. 9.3 kg (20-1/2 lb))
I. Accessory parts
No.
Name
1. Saddle unit
2. Creasing unit
3. Exit tray
4. Shutter
5. Mounting
bracket (right)
6. Mounting
bracket (left)
7. Shutter
mounting
holder
8. Creasing unit
adjusting plate
9. Mounting
bracket cover
SD-505
INSTALLATION MANUAL
Shape
Q'ty
1
4511IXC107DA
1
4511IXC055DA
1
4511U004AA
1
4511IXC024DA
1
4511U006AA
1
4511U007AA
2
4511U008AA
1
4511U009AA
1
4511U011AA
Saddle Stitcher
No.
Name
10. Screw A
(3 × 6 mm)
11. Screw B
(3 × 8 mm)
12. Screw C
(4 × 8 mm)
13. Screw D
(3 × 8 mm)
14. Screw E
(4 × 8 mm)
15. Shoulder
screw A
16. Shoulder
screw B
17. Installation
manual
After unpacking, be sure to get rid of the
packaging materials and keep them out of
the reach of children.
Putting the head in the plastic bag
involves danger of suffocation.
Note:
Take the same procedures, though the machine
illustrations or adjustment screens are different
from the ones in the procedures.
II. When installing to the printers
• This manual provides the illustration of the
machine used as MFP. However, the same instal-
lation procedure is used for the printers.
• For screen adjustment, make sure to use the field
service tools. Refer to the machine installation
manual regarding how to connect and use the
field service tools.
E-1
Applied Machine: FS-519
Shape
Q'ty
2
9646
2
9739
9
4511U012AA
1
9735
1
9J08IXC079DA
1
4511U013AA
2
4511U014AA
1
set
4980IXC019DA
4511-9560-01
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Konica Minolta SD-505
Summary of Contents for Konica Minolta SD-505
- Page 1 SD-505 Saddle Stitcher INSTALLATION MANUAL Applied Machine: FS-519 Note: Name Shape Q’ty Lifting the machine in an awkward position or 10. Screw A transporting it in a poorly balanced position could (3 × 6 mm) result in personal injury. When transporting the...
-
Page 2: Installation Procedures
III. Installation procedures 3. If the finisher is mounted on the machine, remove the finisher. Note: Note: • When mounting the saddle stitcher, mount it For the finisher removal procedure, see installa- before mounting the finisher to the machine. tion manual for finisher. •... - Page 3 9. Remove the guide plate (left) (two screws). 11. Let the connector of the creasing unit into the hole shown in the illustration. Note: 12. Carefully insert the creasing unit into the finisher When mounting the punch kit at that time, it has along the notch provided in the rear of the fin- been removed.
- Page 4 13. Place the creasing unit adjusting plate beneath 17. Connect the connector of the creasing unit. the creasing unit and temporarily secure the unit by tightening screw only temporarily (one screw A furnished with saddle stitcher). 4511IXC083DA 18. Reinstall the cover that has been removed in step 7 (two screws).
- Page 5 20. Reconnect the connector that has been discon- 25. Move the shutter up and down. Release the nected in step 5. shutter from a higher position to check to ensure 21. Reinstall the rear cover that has been removed that the shutter falls by its own weight. in step 4 (four screws).
- Page 6 28. Remove the right and left covers (two screws 31. Secure the mounting brackets in position follow- each). ing the order shown in the illustration (three screw C’s each furnished with the saddle stitcher). 4511IXC114DA 29. Use a nipper, etc. to cut out two separation cov- 4511IXC071DA ers.
- Page 7 34. Reinstall the left exit tray mounting holder that 37. Reinstall the finisher exit tray that has been has been removed in step 27 (one screw). removed in step 26 (two screws). Note: Note: Install the holder at a level one step lower than To prevent problems, be sure to securely tighten where it was removed in step 27.
- Page 8 39. Secure the saddle unit to the mounting bracket 43. Remove the connector cover from the finisher (left) (two screw C’s furnished with the saddle (one screw). stitcher). 44. Use a nipper, etc. to cut out the separation cover. Note: Temporarily tighten the left screw, securely tighten the right screw, and then securely tighten the left screw.
- Page 9 IV. Adjustments <Crease position adjustment> 1. Make a copy in the crease mode. * State the adjustments of A3 here. (Refer to the user’s guide (copy operations)) 2. Fold the copy fed out along the crease. 1. Plug the power cord into the power outlet and 3.
- Page 10 7. Touch “Fold&Staple Pos. Adjustment.” [If the crease deviates as shown below] 11. Using the key, set the numeric value and touch “END.” 4512IXE077DA Exit direction 8. Touch “Fold Position Adjustment.” 4511IXC091DA 12. Touch “END.” 13. Touch “Exit” on the Service Mode screen. 14.
- Page 11 <Staple tilt adjustment> <Staple position adjustment> 1. Load a five-page A4 document in the docu- 1. Load a five-page A4 document in the docu- ment feeding tray. ment feeding tray. 2. Select the center staple mode and make a copy. 2.
- Page 12 8. Touch “Fold&Staple Pos. Adjustment.” [If the staple positions deviate as shown below] 12. Using the key, set the numeric value and touch “END.” 4512IXE077DA Exit direction 9. Touch “Center Staple Position.” 4511IXC094DA 13. Touch “Enter” three times. 14. Touch “Exit” on the Service Mode screen. 15.
Need help?
Do you have a question about the SD-505 and is the answer not in the manual?
Questions and answers