Advertisement
Table of Contents
- 1 Table of Contents
- 2 General Information
- 3 Illustrated Parts Lists
- 4 Attaching Plow to EZ Build Assembly
- 5 Vehicle Side Wiring Diagram
- 6 Drop Speed Adjustment
- 7 Stop Bolt Adjustment
- 8 Mount Plow System to Vehicle
- 9 Dis-Mount Plow System from Vehicle
- 10 Pre-Delivery Inspection
- 11 Accessories
- Download this manual
Form No. 1-1112
May 2014
EZ Build Assembly and Installation
EZ Build Assembly and Installation
41
41200 Drive Pro Plow 7'-6" with E-58H 12V Hydraulic Unit
41275 Lot Pro LD Plow 7'-6" with E-72 12V Hydraulic Unit
and
41250 Drive Pro Plow 7'-6" with E-72 12V Hydraulic Unit
Meyer Products LLC reserves the right, under its continuing product
Meyer Products LLC
improvement program, to change construction or design details,
18513 Euclid Ave. • Cleveland, Ohio 44112-1084
specifi cations and prices without notice or without incurring any obligation.
Phone 216-486-1313
www.meyerproducts.com• email info@meyerproducts.com
© 2012 Printed in the U.S.A.
Advertisement
Table of Contents
Related Manuals for Meyer Lot Pro 41275
Summary of Contents for Meyer Lot Pro 41275
- Page 1 41275 Lot Pro LD Plow 7’-6” with E-72 12V Hydraulic Unit 41250 Drive Pro Plow 7’-6” with E-72 12V Hydraulic Unit Meyer Products LLC reserves the right, under its continuing product Meyer Products LLC improvement program, to change construction or design details, 18513 Euclid Ave.
-
Page 2: Table Of Contents
4. The vehicle must be equipped with a “Heavy Duty Battery” (70 Amp, Hr. Min.), 550 C.C.A. and “Alternator” (60 Amp. Min.) to obtain maximum performance. 5. Follow these instructions explicitly. Warranty does not apply to a Meyer product which has been negligently or improperly assembled or installed. -
Page 3: Illustrated Parts Lists
• Hose 1/4 x 22” Parts indented are included in the carton, bag or assembly under which they are indented. Meyer Products LLC reserves the right, under its continuing product improvement program, to change construction or design details, specifi cations and prices without... - Page 4 41275 E-72 Assembly 56 58...
- Page 5 • Flatwasher 3/8 Parts indented are included in the assembly under which they are indented. Meyer Products LLC reserves the right, under its continuing product improvement program, to change construction or design details, specifi cations and prices without notice or without incurring any obligation.
-
Page 6: Attaching Plow To Ez Build Assembly
Attaching Plow to EZ Build Assembly A. Attach L.H. and R.H. Light Brackets (46 & 47) to the side plates of Lift Frame (12) in Note: Proper tension is attained when Trip Spring (35) coils just begin to separate and the upper two holes using 5/16”-18 x 1-1/4”... -
Page 7: Vehicle Side Wiring Diagram
The blue wire is sensing when the vehicle is in c. Top off the unit to the fi ll line on the reservoir with Meyer M-1 Hydraulic Fluid. reverse in order to operate HFP (Hands Free Plowing). -
Page 8: Drop Speed Adjustment
Check snow plow light blinkers to make sure the wires have not been reversed. Note: All electrical connections should have both ends coated with a dielectric grease, Meyer Part No. 15632, prior to fi nal installation. This will ensure a good connection and help in preventing corrosion. -
Page 9: Mount Plow System To Vehicle
G. Remove weather cover on male end and connect one piece electrical plug. The spring loaded cover will lock one piece plug. Meyer Products assumes no responsibility for installations not made in accordance with these instructions. -
Page 10: Dis-Mount Plow System From Vehicle
C. Remove crankstand from lift frame. G. Disconnect one piece electrical plug and install weather cover on male end. D. Attach crankstand to a-frame H. Back vehicle away from plow assembly. Meyer Products assumes no responsibility for installations not made in accordance with these instructions. -
Page 11: Pre-Delivery Inspection
PRE-DELIVERY INSPECTION Vehicle Make: Vehicle Model: Vehicle Year: Vehicle VIN#: Vehicle FGAWR: Installing Company: Mounting Type: Plow Type: EZ Plus Hydraulic Serial Number: Moldboard Serial Number: All bolts torqued to specifi cation Plow Operation Up Clevis height Suspension interference Plow Operation Left Plow Operation Right Clevis height in inches Diode Installed... -
Page 12: Accessories
16529 Optional Light Guards Meyer 16536 (‘99-07 Ford) Winch Cradle 16537 (‘99 + Chevy) 16539 (‘99 + Dodge) Meyer Products LLC 18513 Euclid Ave. • Cleveland, Ohio 44112-1084 Phone 216-486-1313 (11) www.meyerproducts.com• email info@meyerproducts.com © 2014 Printed in the U.S.A.
Need help?
Do you have a question about the Lot Pro 41275 and is the answer not in the manual?
Questions and answers